Black & Decker BCN115 Originalanweisungen Seite 7

Assembly
Warning! To reduce the risk of serious personal injury, turn
unit off and keep away from the on-off button before making
any adjustments or removing/installing attachments or
accessories. An accidental start‑up can cause injury.
Charging procedure (fig. A)
Warning! Do not use tool while it is connected to the charger.
Insert the charging plug (9) into the charge port (8).
u
Plug the charging plug into any charging port (such as on
u
a computer).
The charging indicator LED (3) will flash red while
u
charging.
The charging indicator LED will change to solid green
u
when fully charged.
Battery can be left charging or charger can be
u
disconnnected.
Important charging notes
The charger and tool may become warm to the touch
u
while charging.
This is a normal condition, and does not indicate a
problem. To facilitate the cooling of the tool after use,
avoid placing the charger or tool in a warm environment
such as in a metal shed or an uninsulated trailer.
If the tool does not charge properly, take the tool and
u
charger to your local service center.
You may charge a partially used battery whenever you
u
desire with no adverse effect on the tool.
Assembly and adjustments
Warning! To reduce the risk of serious personal injury,
turn unit off and keep away from the trigger before making
any adjustments or removing/installing attachments or
accessories. An accidental start‑up can cause injury.
Preparing the tool
Warning! Keep the tool pointed away from yourself and others.
Serious personal injury may result.
Warning! To reduce the risk of serious personal injury, ensure
power switch is in the off position and keep hands away from
trigger and remove staples and brad nails from magazine
before making adjustments.
Warning! NEVER spray or in any other way apply lubricants
or cleaning solvents inside the tool. This can seriously affect
the life and performance of the tool.
Read the Safety Instruction section of this manual.
u
Wear eye and ear protection.
u
Ensure magazine 5 is empty of all fasteners.
u
Place contact trip 4 onto work surface to check for smooth
u
and proper operation of contact trip. Do not use tool if it is
not functioning properly. NEVER use a tool that has the
contact trip restrained in the actuated position.
(Original instructions)
Keep tool pointed away from yourself and others.
u
Loading the tool (Fig. B)
Warning! Keep the tool pointed away from yourself and
others. Serious personal injury may result.
Warning! Always ensure the power switch is in the off position
before loading or unloading.
Warning! Never load staples/brad nails with the contact trip or
trigger activated. Personal injury may result.
Universal compatibility with heavy duty staples 6mm-14mm,
10.6mm crown width, and 15mm brad nails.
Pinch the magazine release clip (6) and pull out the sliding
u
magazine (5).
Load fasteners. Ensure staples are loaded so that crown
u
of the staples sits against inside surface of the magazine.
Note: The head of the brad nail must sit against the left, inside
surface of the magazine. If loaded on right side the magazine
will not close.
Close sliding magazine until the magazine latch clips
u
snuggly in place.
Unloading the tool
Warning! Always ensure the power switch is in the off (0)
position.
Pinch the magazine release clip (6) and pull out the sliding
u
magazine (5) .
Tip the tool to the side until the staples slide freely out of
u
the bottom of the magazine.
Check to ensure no loose staples remain inside magazine.
u
Close sliding magazine fully.
u
Clearing a jammed staple
If a staple becomes jammed in the magazine, keep the tool
pointed away from you and follow these instructions to clear:
Warning! Always ensure the power switch is in the off position
before clearing a jammed staple
Pinch the magazine release clip (6) and remove any
u
loaded staples.
Visually check inside magazine (5) for any jammed
u
staples.
Remove bent staple using pliers if necessary.
u
Reinsert staples into magazine (see Loading the Tool).
u
Operation
Warning! To reduce the risk of serious personal injury,
turn unit off and keep away from the trigger before making
any adjustments or removing/installing attachments or
accessories. An accidental start‑up can cause injury.
Trigger operation (Fig. C)
Warning! Always wear proper eye and hearing protection
when operating tool.
Warning! Keep fingers AWAY from trigger when not driving
staples to avoid accidental fastener discharge. NEVER carry
tool with finger on trigger.
ENGLISH
7