Bosch AXT 22 D Originalbetriebsanleitung Seite 14

14 | English
WARNING: Inadequate extension cables can be
dangerous. Extension cable, plug and socket
must be of watertight construction and inten-
ded for outdoor use.
The connections (plugs and sockets) should be kept dry and
off the ground.
For increased electrical safety use a Residual Current Device
(RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
If the supply cord is damaged, it must be replaced by a
Bosch Service Centre.
Use only extension cords, cables, leads and cable reels that
comply with EN 61242/IEC 61242 or IEC 60884-2-7 and
are of type H05VV-F or H05RN-F.
When using cable drums, these must be completely un-
reeled.
Unpack
Remove the machine from the package.
Assemble the chute (see figures E − F)
Lift back blade cover plate (12).
➊
Hook in chute assembly (8) to the garden product,
➋➌
and then release the blade cover plate (12).
Press the chute (8) down and turn red clamping
➍
knob (9) fully clockwise to lock the chute (8) in
place, approximately 5x full turns of the clamping
knob (9) are required.
Operation
Starting Operation (see figure G)
Always place the machine on firm level ground. During
u
operation, do not tilt or move.
The motor will coast after switching off!
u
Remove earth from roots. Foreign material such as stones,
glass, metals, fabrics or plastics must not enter the chute as-
sembly (8). Otherwise this could damage the cutting system
(15).
The chute assembly (8) must be empty.
Starting
Press green button (4).
Stopping
Press the STOP button (5).
In order to protect mechanical parts, wait for 2 seconds be-
fore restarting the machine.
Restarting Protection
A mains failure causes machine to switch off.
The machine cannot restart on its own when the power re-
turns.
F 016 L94 417 | (28.10.2022)
Return Motion
Press and hold the reverse button (6) to reverse the feed.
The cutting system (15) runs backward and frees jammed
material.
Overload Protection
Overloading (e. g. blocking of the cutting system (15))
causes the machine to stop after a few seconds, that time a
beep is audible.
Press the red STOP button to clear the error. After blocking
the tool can start in reverse direction.
Press and hold the reverse button (6) to reverse the cutter
to unblock.
In case of starting in the same direction the tool won't start
and beeps.
If the blockage cannot be cleared the pressure plate (14) will
need to be moved away from the cutter.
The adjustment knob (10) will need to be turned a counter-
clockwise direction a small amount until the jammed mater-
ial is clear. The pressure plate (14) will need adjustment
(see "Pressure Plate Adjustment (see figure H)", page 15).
Heavy blockage
If reversing or adjusting the pressure plate does not remove
the blockage, stop the machine and remove the plug from
the mains.
Turn the red clamping knob anticlockwise, pull the blade
cover plate backwards and lift off the chute assembly. Lift up
the blade cover plate and carefully remove all residues from
the cutting system. Wear protective gloves and be careful
with the sharp blades of the cutting system.
Working Advice
Wear eye protection, hearing protection and safety
u
gloves at all times whilst operating the machine.
Always check before use that the collection box and
u
chute assembly are fitted correctly.
The machine is fitted with sensors. If the collection box (11)
and the chute assembly (8) are not correctly positioned, the
machine will not start and the buzzer beeps (on AXT 23
TC/25 TC/2550 TC also the 2 LEDs (13) flash).
Press the red STOP button to clear the error.
Insert the material to be shredded. The material will be fed
by the cutting system (15) without further assistance.
Longer material standing out from the machine could
u
lash out when being pulled in by the knives! Please
keep at safe a distance!
Only insert as much material so that the chute assembly (8)
will not be blocked up.
Shred withered, moist material and garden waste which has
been stored for some days alternately with branches. This
prevents the cutting system (15) from clogging.
Do not fill soft waste such as kitchen rubbish into the shred-
der but compost directly.
Bosch Power Tools