Bosch AXT 22 D Originalbetriebsanleitung Seite 13

b)
(16) Hex key
a) country specific
Technical Data
Quiet-shredder
Article number
Power consumption, S 6
A)
(40/60 s)
Power consumption, S 1
Cutting head speed min
Cutting system
B)
Branch diameter, max. mm
Collection box
Weight according to
EPTA‑Procedure
01:2014
Protection class
A) The S 6 operating mode (40 %) indicates a load profile of 40 s load and 60 s idle time. For practical application, continuous operation is
permitted.
B) Depending on the hardness of the wood.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system condi-
tions. Malfunctions are not to be expected for system impedances below 0,36 ohm. If in doubt, please contact your electricity supplier.
Noise/Vibration Information
Noise emission values determined according to EN 50434
Typically the A-weighted noise levels of the product are:
– Sound pressure level
– Sound power level
– Uncertainty K
That the declared vibration total value(s) and the declared
noise emission value(s) have been measured in accordance
with a standard test method and may be used for comparing
one machine with another.
That the declared vibration total value(s) and the declared
noise emission value(s) may also be used in a preliminary as-
sessment of exposure.
That the vibration and noise emissions during actual use of
the machine can differ from the declared total value depend-
ing on the ways in which the machine is used; and of the
need to identify safety measures to protect the operator that
are based on an estimation of exposure in the actual condi-
tions of use (taking account of all parts of the operating cycle
such as the times when the machine is switched off and
when it is running idle in addition to the trigger time).
Bosch Power Tools
AXT 22 D AXT 25 D
3 600 H03 0.. 3 600 H03 1..
W 2200
W 2000
-1
40
Drum
38
l 53
kg 31.3
/ I
Assembly
For Your Safety
u
Observe correct mains voltage: The voltage of the power
source must agree with the voltage specified on the name-
plate of the unit. Equipment marked with 230 V can also be
connected to 220 V or 240 V.
The circuit must at least be protected as follows:
AXT 22 D/25 D/23 TC/25 TC/2550 TC = 13 A
An extension cable with a cross section that is too small
causes a distinct reduction in the performance capabilities
of the machine. For cables to 25 m in length, a cross section
of at least 3 x 1.5 mm
25 m in length, the cross section must be at least 2.5 mm
b) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
AXT 23 TC AXT 25 TC
3 600 H03 2.. 3 600 H03 3..
2500 2300
2300 2100
40 40
Drum Turbine
40 42
53 53
31.3 30.5
/ I / I
3 600 H03 0..
3 600 H03 1..
dB(A) 81
dB(A) 89
dB = 3,0
Warning! Switch off, remove plug from mains before
adjusting or cleaning. The same applies when the
mains cable is damaged, cut or entangled.
2
is required, for cables more than
English | 13
AXT 2550 TC
3 600 H03 3..
2500 2500
2300 2300
40 40
Turbine Turbine
45 45
53 53
30.5 30.5
/ I / I
3 600 H03 2..
3 600 H03 3..
82
90
= 2,0
2
.
F 016 L94 417 | (28.10.2022)