Air Supply; Operating Procedures - MAG TOOLS MPF970501 Bersetzung Der Originalanweisungen

Air Supply

The recommended hook-up is shown in the following
illustration. Pneumatic tools operate on a wide range of air
pressures. For maximum efficiency and longer tool life, the
pressure of the air supplied to these tools MUST not exceed the
rated PSI at the tool when the tool is running. Using a higher
than rated pressure will cause faster wear and drastically shorten
the tool's life. A higher air pressure can also cause an unsafe
condition and explosion.
The inside diameter of the hose should be increased to
compensate for unusually long air hoses 7.6 m. Minimum
hose diameter should be 10 mm I.D. and fittings should have
6.35 mm NPT thread.
The use of air line lubricators and air line filters is recommended
to prevent water in the line that can damage the tool. Drain the
air tank daily. Clean the air inlet filter screen on at least a weekly
schedule to remove accumulated dirt or other matter that can
restrict air flow.
The tool's air inlet used for connecting an air supply has
standard 6.35 mm NPT American thread.
nOtE: An air filter unit should be placed between air
compressor and air lubricator to promote clean air supply to
the impact wrench. Water, dirt, and scale can damage the
impact wrench.
EMERGENCY
GATE VALVE
Prepping the Air Tool

WARNING: Risk of unsafe operation. Firmly grasp air hose
with hand when installing or disconnenting to prevent
hose whip.

WARNING: Risk of bursting. Too much air pressure causes
a hazardous risk of bursting. Check the manufacturer's
maximum pressure rating for air tools and accessories.
The regulator output pressure must never exceed the
maximum pressure rating.
• Drain water from air compressor tank and condensation
from air lines. (Please refer to air compressor's
operation manual.)
Lubricate the tool. (Please refer to the Maintenance section
•
in the manual.)
• Connect the air ratchet to air source with the hose of
recommended size.
Proper Hand Position (Fig. A)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.

Operating Procedures

Air Supply

CAUTION: This air tool requires lubrication BEFORE initial
use, also before and after each additional use.

WARNING: Use a clean lubricated air supply that will give
a measured air pressure at the tool of 90 PSI/6.2 bar when
the tool is running with the trigger fully depressed.
Use recommended hose size. It is recommended that the tool is
connected to the air supply.
Do not connect the tool to the air line system without
incorporating an easy to reach and operate air shut off valve.
The air supply should be lubricated. It is strongly recommended
that an air filter, regulator, lubricator (FRL) is used as this will
supply clean, lubricated air at the correct pressure to the tool.
Details of such equipment can be obtained from your supplier.
If such equipment is not used then the tool should be lubricated
by shutting off the air supply to the tool and then depressurizing
the line by pressing the trigger on the tool. Disconnect the
air line and pour into the air inlet 1 teaspoon of a suitable
pneumatic motor lubricating oil, preferably incorporating a rust
inhibitor. Reconnect tool to air supply and run tool slowly for a
few seconds to allow air to circulate the oil.
Lubricate tool daily if used frequently, or when it starts to slow
or lose power.
Start‑Up (Fig. A)
1. Turn on the air compressor and allow the air tank to
be filled.
2. Set the air compressor regulator to 90 PSI (6.2 Bar) This air
tool operates at a maximum of 90 PSI (6.2 Bar) air pressure.
3. Depress the Variable speed trigger
the tool. The more you squeeze the trigger, the faster the
tool will operate.
Shut‑Down (Fig. A)
1. Release the Variable speed trigger
the tool.
EnGLIsh
1 to start operating
1 in order to stop
19