Technical Data; English (Original Instructions) - MAG TOOLS MPF970501 Bersetzung Der Originalanweisungen

1/2" AIR IMPACT WRENCH
MPF970501, MPF972501
The Mac Tools™ MPF970501 and MPF972501 are precision-built
tools, designed for driving, tightening and loosening threaded
fasteners, usually nuts and bolts, when fitted with a suitable
impact socket. These tools will deliver efficient, dependable
service when used correctly and with care. As with any
fine power tool, for best performance the manufacturer's
instructions must be followed. Please study this manual before
operating the tool and understand the safety warnings and
instructions. The instructions on installation, operation and
maintenance should be read carefully, and the manual kept for
reference. nOtE: Additional safety measures may be required
because of your particular application of the tool. Contact your
Mac Tools representative or distributor with any questions
concerning the tool and its use.

Technical Data

Square drive in / mm
bpm
Impact Rate
fwd / rev
Breakaway torque ft‑lbs / Nm
Noise Level Pressure
dB(A)
(ISO 15744)
Noise LevelPower
dB(A)
(ISO 15744)
Vibration level
m/s 2
(ISO 28927‑2 )
Average air
cfm / I/min
consumption
Working pressure psi / bar
Weight lbs / kg
Dimensions in / mm
* = measurement uncertainty in dB(A)
** = measurement uncertainty in m/s
6.35 mm NPT
High Flow Fitting
MPF970501 MPF972501
.5 / 13 .5 / 13
1030 / 1120 1010 / 1060
1100 / 1490 1100 / 1490
90 / 3* 90 / 3*
101 / 3* 101 / 3*
5.2 / 1.5** 5.2 / 1.5**
5.2 / 147.2 5.2 / 147.2
90 / 6.2 90 / 6.2
6.2 / 2.8 6.4 / 2.9
7.5 X 2.8 X 7.6 / 9.6 X 2.8 X 7.6 /
190 X 70 X 193 243 X 70 X 193
2
Air Hose
10 mm
I.D. Min
EC‑Declaration of Conformity
Machinery Directive
1/2" AIR IMPACT WRENCH
MPF970501, MPF972501
MAC TOOLS declares that these products described under
Technical Data are in compliance with: ISO 11148-6:2012.
These products also comply with Directive 2006/42/EU. For
more information, please contact MAC TOOLS at the following
address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of MAC TOOLS.
Markus Rompel
Vice-President Engineering, PTE-Europe
MAC TOOLS, Egide Walschaertsstraat 14-18
2800 Mechelen, Belgium
09.08.2021
DECLARATION OF CONFORMITY
THE SUPPLY OF MACHINERY (SAFETY)
REGULATIONS 2008
1/2" AIR IMPACT WRENCH
MPF970501, MPF972501,
MAC TOOLS declares that these products described under
Technical Data are in compliance with:
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended),
ISO 11148-6:2012.
For more information, please contact MAC TOOLS at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of MAC TOOLS.
Karl Evans
Vice President Professional Power Tools EANZ GTS
MAC TOOLS UK, 270 Bath Road, Slough
SL1 4DX
England
09.08.2021
EnGLIsh
15