Herunterladen Inhalt Inhalt Diese Seite drucken

Pannello Frontale; Front Panel - Cicognani INDY BASS AMP 800H Benutzerhandbuch

Inhaltsverzeichnis

Werbung

PANNELLO FRONTALE

1)INPUT one / INPUT two°
Prese jack mono da 6.3mm per collegare il basso, basso
acustico, contrabasso.
2)GAIN°
Questo controllo regola il guadagno d'ingresso e quindi
anche il livello di saturazione e la distorsione.
3/4/5/6)COMPRESSOR°
Questo sistema riduce la dinamica del segnale; i picchi di
volume vengono abbassati ed accentuati i segnali bassi
riducendo così la differenza tra i passaggi più alti e
silenziosi di un segnale. In questo modo si ottiene un
suono molto più corposo.
5
Il pulsante ( ) attiva il circuito elettronico del
compressore; il livello è regolato dalla rispettiva
manopola ( ) e l'accensione del led ( ) ne indica
3
l'attivazione. L'accensione del led ( ) indica il verificarsi di
salti di picco; in questo caso è necessario regolare il
livello di compressione.
7) SOLO°
Controlla il livello del volume in occasione di parti
solistiche.
8/9/10) CH SWITCH°
Pulsante per la selezione dei due differenti livelli ( SOLO
e VOLUME). L'accensione dei rispettivi led ne indica
l'attivazione.
11) VOLUME°
Controllo di livello del volume canale
12/14/16) BASS / MIDDLE / TREBLE°
Regolazione per l'esaltazione o l'attenuazione delle
frequenze basse,medie e acute.
13/15) BASS BOOST / TREBLE BOOST°
L'attivazione di questi controlli esalta ulteriormente in
modo marcato rispettivamente le basse e le alte
frequenze
17) DUALBASS/DUALCH°
Seleziona il modo di configurazione: con due strumenti
contemporaneamente (DUAL BASS) o con due canali
(DUALCHANNEL) uno o due strumenti alternati.
18)MIDISTORE°
Tasto per la memorizzazione di tutte le funzioni sul
preset MIDI. Il sistema di trasmissione e ricezione del
protocollo MIDI è in configurazione Omnimode, quindi
non necessita di nessuna impostazione del canale di
trasmissione midi.
19)MASTER°
Controllo generale di livello del canale; accertarsi, prima
di accendere l'ampli, che la manopola sia posizionata in
senso antiorario.
20/21)TUBE HEATING / PLAYING°
All'accensione del sistema attendere che il led rosso
TUBE HEATING (pre-riscaldamento delle valvole) si
spenga e si accenda il led verde PLAYING.
2 2 ) °
I n t e r r u t t o r e g e n e r a l e d i a c c e n s i o n e
dell'amplificatore.
I
6
4

FRONT PANEL

UK
1)INPUT one / INPUT two°
6.3 mm mono jack socket for connecting the bass guitar,
the acoustic bass guitar, the double bass.
2)GAIN°
This control adjusts the input gain and, thus, also the
saturation level and the distortion.
3/4/5/6)COMPRESSOR°
This system reduces signal dynamics: volume peaks are
lowered and bass signals are boosted, thus reducing the
difference between the highest and lowest signal
transitions. In this way, a much denser sound is obtained.
The button (5) switches on the electronic circuit of the
compressor; the level is adjusted using its knob (3). The
LED (6) lights up to indicate that it is on. When it lights up,
the LED (4) indicates signal peaks; in this case, the
compression level shall be adjusted.
7) SOLO°
It controls the level of the volume during solo pieces.
8/9/10) CH SWITCH°
This button selects the two different levels (SOLO and
VOLUME). The respective LED will light up to indicate
that they are on.
11) VOLUME°
Channel volume level control
12/14/16) BASS / MIDDLE / TREBLE°
This control adjusts the boosting or attenuation of bass,
middle and treble frequencies.
13/15) BASS BOOST / TREBLE BOOST°
Switching on these controls, the bass and treble
–respectively- are further boosted.
17) DUALBASS/DUALCH°
It selects the configurationmode: with two instruments at
the same time (DUAL BASS) or with two channels (DUAL
CHANNEL) one or two alternate instruments.
18)MIDISTORE°
This button is used to store all the functions on the MIDI
preset. The transmission and reception system of MIDI
protocol is set in Omnimode and, hence, it does not need
any setup of themiditransmission channel.
19)MASTER°
Channel level main control; before switching on the
amplifier, make sure that the knob is turned
anticlockwise.
20/21)TUBE HEATING / PLAYING°
When switching on the system, wait for the "TUBE
HEATING" red LED (tubes preheating) to go out, and for
the "PLAYING" green LED to light up.
22)°
Amplifier main power switch.
5

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis