What Is Included; Signal Connections; Control Personalities; Art-Net™ Connection - Chauvet Professional Maverick Storm 2 BeamWash Schnellanleitung

What is Included

• Maverick Storm 2 BeamWash
• Seetronic Powerkon IP65 to bare wire power cord
AC Power
This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.
AC Plug
Connection
AC Live
AC Neutral
AC Ground
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
Replacing the Fuse
1. Disconnect the product from power.
2. Using a Phillips-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove blown fuse and replace with a good fuse of the same type and rating.
4. Screw the fuse holder cap back in place and reconnect power.

Signal Connections

You can link the Maverick Storm 2 BeamWash to a controller or controller software using a DMX connection, an Ethernet
connection, or both. If using other Art-Net™, sACN, or Kling-Net-compatible products with the
Maverick Storm 2 BeamWash, you can control each individually on a single network. See the User Manual for information
about how to connect and configure the product for these signals.

Control Personalities

The Maverick Storm 2 BeamWash
Single Control
Basic (31-channel)
Standard (143-channel)
Advanced (263-channel)
Tour (325-channel)
Basic2 (37-channel)
In Dual Control mode, the Movement protocol and the Pixels protocol cannot be the same.
DMX Connection
The Maverick Storm 2 BeamWash will work with a DMX controller using a 5-pin DMX serial connection or a wireless DMX
connection. A DMX Primer is available from www.chauvetprofessional.com.
Art-Net™ Connection
Art-Net™ is an Ethernet protocol that uses TCP/IP which transfers a large amount of DMX512 data using an Neutrik®
etherCON® RJ45 connection over a large network. An Art-Net™ protocol document is available from
www.chauvetprofessional.com. Chauvet Professional recommends using unicast Art-Net™ for best results.
Art-Net™ designed by and copyright Artistic Licence Holdings Ltd.
sACN Connection
Also known as ANSI E1.31, Streaming-ACN is an Ethernet protocol that uses the layering and formatting of Architecture
for Control Networks to transport DMX512 data over IP or any other ACN compatible network.
Kling-Net Connection
Kling-Net is a network protocol that allows auto configuration of display devices using an ethernet connection. Refer to
the ArKaos software manual for detailed instructions on programming this product.
For smooth-running operation, ArKaos Kling-Net requires a gigabit (1000 Mbps) Ethernet card and
network router.
ArKaos Kling-Net will only run Standard Pixels or Basic Pixels mode.
RDM (Remote Device Management)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally
along existing DMX cabling. Check the DMX controller's User Manual or with the manufacturer as not all DMX controllers
have this capability. The Maverick Storm 2 BeamWash supports RDM protocol that allows feedback to make changes to
menu map options. Download the User Manual from
Maverick Storm 2 BeamWash QRG Rev. 2
QUICK REFERENCE GUIDE
Wire (U.S.)
Black
White
Green/Yellow
uses
DMX, Art-Net™, sACN, Kling-Net, and WDMX for its control personalities:
Dual Control Movement
Basic (11-channel)
Standard (34-channel)
Advanced (45-channel)
www.chauvetprofessional.com
• 2 Omega Brackets with mounting hardware
• Quick Reference Guide
Wire (Europe)
Brown
Blue
Green/Yellow
Dual Control Pixels
Basic (93-channel)
Standard (112-channel)
Advanced (224-channel)
for more details.
EN
Screw Color
Yellow/Brass
Silver
Green
2