Rechargeable Battery (Not Included In The Scope Of Delivery) - Bosch AdvancedGlue 18V Originalbetriebsanleitung

(10) Feed trigger
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless glue gun
Article number
Rated voltage V=
A)
Heat-up time approx. min
Gluing temperature (can
be selected)
Max. gluing capacity g/min
Glue stick
– Diameter mm
– Length mm
A)
Operating time per bat-
tery charge up to
Weight according to EPTA-
B)
Procedure 01:2014
Permitted ambient tem-
perature
– During charging
– During operation and
during storage
Recommended re-
chargeable batteries
Recommended battery
C)
chargers
A) Measured at 20–25 °C with battery PBA 18V 2.5Ah W-. and
processing temperature 200 °C.
B) Depends on battery in use
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Rechargeable battery (not included
in the scope of delivery)
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your glue gun.
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
the first time.
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
Bosch Power Tools
AdvancedGlue 18V
3 603 B64 8..
18
2
°C 130
°C 200
20
11
45−200
10 glue sticks
kg 0,68−0,99
°C 0...+35
°C +5...+40
PBA 18V...W-.
AL 18...
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
Battery charge indicator
The battery charge indicator indicates the remaining battery
capacity when the glue gun is switched on.
If the temperature selection button (7) or (9) flashes red
after heating, the battery has less than 30 % of its capacity
and should be charged.
If the temperature selection button (7) or (9) flashes red,
the battery is completely discharged and must be charged.
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Operation
Starting Operation
Switching On and Off
– To switch on the glue gun, press the on/off button (8).
The glue gun heats to the last set processing temperature
(130 °C or 200 °C).
The relevant temperature selection button (7) or (9) will
flash green while the tool is heating up. Once it is continu-
ously lit green, the glue gun is ready to use.
If you change the processing temperature during operation,
the relevant temperature selection button (7) or (9) will
flash green until the target temperature required is reached.
The cooling process from 200 °C to 130 °C may take several
minutes.
– To switch off the glue gun, press and hold the on/off
button (8) until the LED for the relevant temperature se-
lection button (7) or (9) goes out.
Note: If the glue gun is not used for longer than 10 minutes,
it will switch off automatically to save energy.
– If the temperature selection button (7) or (9) lights up
red continuously after switching on again, you must
charge the battery.
Safely place the glue gun down after use and let it cool
u
completely before packing it away. The hot nozzle can
cause damage.
Working Advice
Keep people and animals away from the hot adhesive
u
and the nozzle tip. Adhesive and nozzle tip will heat up to
approx. 200 °C, posing a risk of burns. If hot adhesive
English | 11
1 609 92A 6H1 | (22.04.2022)