Preparation; Anti-Tip Bracket - Sub-Zero Classic Serie Installationsanleitung

Site Preparation

Preparation

Uncrate the unit and inspect for damage. Remove the
wood base and discard the shipping bolts and brackets.
Remove and recycle packing materials. Do not discard the
kickplate, anti-tip brackets, and hardware.
Completely retract the front leveling legs to allow the unit
to be moved into position. The front and rear leveling legs
can be adjusted from the front once the unit is in position.
Remove the drain pan from the base of the unit to avoid
damage and to allow for proper placement of the appli-
ance dolly.
The grille assembly should be removed prior to moving the
unit. To remove, pull out on the bottom edge of the grille
and rotate upward. Loosen the back two grille mounting
screws and remove the front two grille mounting screws.
Refer to the illustrations below. With the grille held firmly,
pull forward to remove.
BACK GRILLE
SCREW
FRONT
GRILLE SCREW
Grille removal Grille mounting screws
6 | English

Anti-Tip Bracket

WARNING
To prevent the unit from tipping forward, the anti-tip
brackets must be installed.
The two anti-tip brackets must be installed exactly 610 mm
from the front of the opening to the back of the brackets
and a minimum of 102 mm from the sides of the opening.
This depth will increase to 665 mm for a flush inset instal-
lation based on 19 mm thick panels. Failure to properly
position the anti-tip brackets will prevent proper engage-
ment.
Use all anti-tip bracket hardware as instructed for wood or
concrete floors.
IMPORTANT NOTE: For wood or concrete floor applica-
tions, if the #12 screws do not hit a wall stud or wall plate,
use the #8 screws and #12 washers with the wall anchors.
IMPORTANT NOTE: In some installations the subflooring
or finished floor may necessitate angling the screws used
to fasten the anti-tip brackets to the back wall.
ANTI-TIP HARDWARE
2 Anti-tip brackets
12 #12 x 64 mm pan head screws
4
3/8"–16 x 95 mm wedge anchors
12 #12 flat washers
4 #8–18 x 32 mm truss head screws
®
4 Nylon Zip-it wall anchors
WOOD FLOOR APPLICATION
After properly locating the anti-tip brackets in the open-
ing, drill pilot holes 5 mm diameter maximum in the wall
studs or wall plate. Use the #12 screws and washers to
secure the brackets. Verify the screws penetrate through
the flooring material and into the wall studs or wall plate a
minimum of 19 mm. Refer to the illustration below.
CONCRETE FLOOR APPLICATION
After properly locating the anti-tip brackets in the opening,
drill pilot holes 5 mm diameter maximum in the wall studs
or wall plate. Drill 10 mm diameter holes into the con-
crete a minimum of 38 mm deep. Use the #12 screws and
washers to secure the brackets to the wall, and use the 3/8"
wedge anchors to secure the brackets to the floor. Verify
the screws penetrate the wall studs or wall plate a mini-
mum of 19 mm. Refer to the illustration below.
610
mm
102 mm 102 mm
MIN MIN
FINISHED FINISHED FINISHED
FLOORING FLOORING
FLOORING
WALL PLATE WALL PLATE WALL PLATE
SUBFLOORING SUBFLOORING SUBFLOORING
1 38 mm / "
1
2
WOOD FLOOR CONCRETE CONCRETE
MIN min
FLOOR FLOOR
Wood floor Concrete floor
CONCRETE WEDGE ANCHOR INSTALLATION
1 Drill a 10 mm diameter hole any depth exceeding the
minimum embedment. Clean the hole or drill additional
depth to accommodate the drill fines.
Assemble the washer and nut flush with the end of
2
anchor to protect threads. Drive the anchor through
the material to be fastened until the washer is flush with
the surface material.
3 Expand the anchor by tightening the nut 3–5 turns past
hand-tight position or to 34 newton-meters of torque.
WARNING
Verify there are no electrical wires or plumbing in the
area which the screws could penetrate.
CAUTION
Always wear safety glasses and use other neces-
sary protective devices or apparel when installing or
working with anchors.
Anchors are not recommended for use in lightweight
masonry material such as block or brick, or for use
in new concrete which has not had sufficient time to
cure. The use of core drills is not recommended to
drill holes for the anchors.
610
mm
(38)