Before First Use - Inventum GF432-GF442 Gebrauchsanweisung

or is it not handled in accordance with the instruction
manual, the full responsibility for any consequences will
rest with the user. Any damages to the product or other
things are not covered by the warranty.
2 | bEFoRE FIRST USE
Before you use the appliance for the first time, please do
as follows: Carefully unpack the appliance and remove all
the packaging material. Keep the material (plastic bags and
cardboard) out of reach of children. Check the appliance
after unpacking for any visible damage, possible from
transportation. Place the appliance on a stable and heat
resistant surface.
remove the lid and the basket. take out the heating
element by pulling it straight up and also remove the
reservoir.
Clean the lid, the basket and the reservoir with warm
soapy water. Dry the parts thoroughly. Make sure that the
parts are completely dry.
Wipe the exterior with a damp cloth and dry thoroughly.
Assemble the fryer.
fill the reservoir with liquid frying oil between the
minimum and maximum level, approx. 3 liters or 4 liters,
depending on the model. ensure that you don't add
less than the minimum capacity or over the maximum
capacity. inside the reservoir you will find two lines which
indicate the minimum and maximum level.
Attention: this fryer may only be used with liquid frying
oil. Never use hard fats.
the handle of the basket can be stored in the basket by
folding it in. squeeze the two handle wires together and
push the handle forwards over the locking clip.
only store the handle when the oil is fully cooled down.
Ensure the handle is folded back before operating the
fryer again!
For the best result in a cool zone fryer, always fry
without using the lid.
3 | DESCRIpTIoN oF bUTToNS & mENUS
SELECT
By pressing the SELECT button the user can select the
next menu (combination of specific temp and time). every
time the user presses the button it will jump to the next
menu. from P190 - P180 - P170 - P150 - Manual.
P190
P170
P180
P150
Manual
Changing the temperature of a selected menu
automatically brings the setting to mANUAL. you can
select the required temperature in steps of 5 degrees
between 100°C and 190°C.
START/STop
the START/STop button has two functions:
- start/ stop preheat function (not for Aquaclean menu)
- start/stop frying time
pREHEAT
After the menu has been selected and the user presses the
START/STop button the fryer will start preheating. During
the preheating the p in the LeD display will blink every
second.
Note: during preheating only the START/STop button
will work. When the START/STop button is pressed while
preheating the preheating will stop, the p will stop blinking
and another menu can be selected.
FRYING TImE
if preheat is finished and the fryer has reached the required
temperature the display will show the frying time.
the user can modify the standard frying time of 03:00
minutes by pressing the Up or DoWN button in steps
of 5 seconds. Minimum is 5 secondes and maximum is
15 minutes. After the frying time has been set and the
user presses the START/STop button the frying time will
countdown. When the frying time has reached 00:00 the
fryer will beep for 2 seconds every 15 seconds, indicating
that the time has stopped.
if the START/STop button is pressed when the counter is
counting down the time will stop.
Note: if START/STOP has not been pushed within 15
minutes after preheating the fryer will cool down and
the display will show the pre-selected menu again. When
the frying time has stopped (or the user stopped the
countdown) the fryer will cool down after 15 minutes and
the display will show the pre-selected menu again.
During countdown only the START/STOP button will work.
9
Clean