Texas Equipment LMX2037 Bedienungsanleitung Seite 13

Mounting
Unpacking
Remove the mower from the box by pulling the machine
out.
Warning: Ensure that the cable is not pinched.
Handlebar: Fig. 3+4
1. Attach the lower handlebar (3) on the lawn mower
and fix it with the quick fix knops (14-15) in both
sides. Do not overtighten the knops! Fig.3
2. Attach the upper handlebar (2) on the lower
handlebar (3). Fasten with the quick fix knops (16-
17) in both sides. Fig. 4
3. Customize the cable and secure with cable clamp
Fig. 4 (2)
Assembly the grass collector: Fig. 5
1. Click the frame to the grass collector.
Mounting the grass collector: Fig. 8
2. Attach the grass collector behind the lawn mower
under the rear deflector guard.
Mulching plug: Fig. 9
1. Insert the mulching plug (23), if you want to mow with
mulching functionality.
NB Don't use the grass collector
Important: Remember to remove the mulching plug,
when using the grass collector.
Battery
Warning: Do not try to disassemble, short circuit or put
it to extreme heat or fire, as it can cause serious inquiry
and permanent damage to the battery!
Battery pack is not fully charged when delivered.
Charging
•
Only use the original charger with
art. no. 90063242
•
Before the battery is being used the first time, it is
recommended to fully charge it first.
LED lights
All LEDs are lit
LED 1, LED 2, LED 3
are lit.
LED 1, LED 2
are lit.
LED 1 are lit
LED 1 flashes
Note: The indicator lighs is only indicative indications
and is not accurate power indications.
Important: To protect the battery from total discharge,
the machine will stop, when the battery is nearly empty.
The machine must not be started up again after
automatic shutdown, as it can damage the battery.
Battery Pack
Fully charged (75-
100%).
The battery pack is
50%-75% charged
The battery pack is
25%-50% charged.
The battery pack is
0%-25% charged
The battery pack is
empty. Charge the
battery.
The battery must be recharges before the work can
continue.
Charging
A full charge takes around 60 min for 2.0 Ah batteri
and 120 min for 4.0 Ah battery.
•
Only use the original charger*
•
Do not try to charge other type of batteries in the
charger, other than the original batteries with art.
no. 90063245 (2.0 Ah) or 90063246 (4.0 Ah).
•
Keep the charger in a dry and warm environment
(10-25 degrees C) and only use it indoor. It
should be connected to a normal 230V AC
socket.
•
Before the battery is being used the first time, it is
recommended to charge it fully.
•
The surface of the battery can become warm
during charging. This is normal.
•
Do not cover battery or charger during charging.
Allow free ventilation of air.
Insert the battery into the slots of the charger and
slide it into place until it locks. Fig.6 (13)
There are 4 lights on the charger indicating the status
and state of charge of the battery
Important: The charger will stop, when the battery is
full. However, it is not recommended to leave the
battery in charger for more than 24 hours.
It is recommended to drain the battery completely and
fully charge it whenever possible, as it can increase
the health of the battery. But partial charge will not
damage the battery.
To remove the battery from the charger, hold the
button down and pull the battery out.
Before winter storage, the battery should be fully
charged and kept warm at 10-20 degrees C. Charge it
every 3 months. Make sure to keep ventilation holes
clean and free from dirt.
Store the charger indoor between 5-25 degrees C.
13
Status
Charging
Fully charged
Evaluate
Defective