Panasonic EY3760 Bedienungsanleitung Seite 6

II. ASSEMBLY (EY3760/EY3740)
1. To insert the battery pack; (fig.1)
Line up the alignment marks and attach the
battery pack.
•
Slide the battery pack until it locks into position.
2. To remove the battery pack:
Push on the button from the front to release the
battery pack.
3. Shoulder strap (fig.2)
Follow the steps to make the loop at the buckle.
Make sure the strap is firmly fixed on the
flashlight.
ASSEMBLY (EY3794)
1. To insert the battery pack; (fig.1)
Slide the battery pack in place at the bottom of
the flashlight. The battery should snap into
place. If this is loosen, it has not been properly
connected.
Make sure the battery is securely connected
to the flashlight.
2. To remove the battery pack;
Press the two tabs on the sides of the battery
pack. Slide the battery pack out of the flashlight.
3. Shoulder strap (fig.2)
Follow the steps to make the loop at the buckle.
Make sure the strap is firmly fixed on the flashlight.
III. OPERATION
1. Press the switch to light on.
2. Head angle adjustment; (fig.3)
Head angle can be changed at 4-locking
positions for desired angle.
3. When it is placed away from you, make sure it
will not be tumble.
4. When the battery capacity level gets low, Iow
voltage indicator will start to blink. Then charge
the battery pack.
5. Press the switch to light off after use.
CAUTION:
•
Read the instruction manual of the charger
to charge the battery pack, and how to
handle battery pack.
VI. SPECIFICATIONS
Model no. EY3760
Bulb type 21.6 V Xenon 0.49 A
Size
(10-63/64" 4-7/8" 3-35/64")
318 g (0.69 lbs)
Weight
Battery Li-ion battery pack
packs EY9L60/EY9L61
21.6 V DC
Battery
(3.6 V 6 cells)
voltage
All manuals and user guides at all-guides.com
EY3740
14.4 V Xenon 0.55 A
279 124 90 mm
310 g (0.68 lbs)
Li-ion battery pack
EY9L40/EY9L41
14.4 V DC
(3.6 V 4 cells)
‑ 6 ‑
IV. MAINTENANCE
•
To make any adjustments, changing accessory,
or storing the flashlight, remove battery pack
from the flashlight.
•
To clean the flashlight, wipe with a dry, soft
cloth.
How to replace the new bulb. (fig.4)
1. Take off the ring ( )
1
2. Match the joint part A and B, then remove the
bulb. ( 2 3 , )
3. Install the new bulb and turn to hold firmly.
( 4 5 , )
4. Fit the ring. ( )
1
Lens, reflector, and bulb are hot immediately
after use. Wait a while before replacing the
bulb after switch off.
* To purchase a new bulb, please consult your
authorized dealer. (Please always use the
genuine bulbs.)
V. ACCESSORIES
Battery Pack
•
See the Specification.
Battery Charger
•
For inquiries please contact an authorized dealer.
EY3794
12 V Xenon 0.7 A
270 91 90 mm
(10-5/8" 3-37/64" 3-35/64")
270 g (0.59 lbs)
Ni-Cd battery pack
EY9005, EY9006, EY9106, EY9001, EY9101
Ni-MH battery pack
EY9200, EY9201
12 V DC (1.2 V 10 cells)