Standard Equipment; Turning On The Machine - Virutex SSB65 Gebrauchsanweisung

carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in thi this manual. Any other
use of the tool is strictly forbidden.
Before inserting the battery cartridge into the tool, always
check to see that the On/Off trigger 4 (Fig. 1) actuates
properly and returns to the "OFF" position when released.
4. COMPONENTS
DESCRIPTION (See Fig. 9)
1. Handle
2. Auxiliary handle
3. Lock-on button
4. Switch
5. Head
6. Bolt
7. Blade
8. Support plate
9. Battery (not included)
10. Battery lock-off button
11. Charger
12. LED light

5. STANDARD EQUIPMENT

- Allen key
- Instructions manual.
- Warranty
6. SPECIFICATIONS OF THE TOOL
The cordless reciprocating saw is designed for cutting
wooden, plastic and metal (non ferrous) workpieces.
Special saw blades extend significantly the application
range of the power tool and allows for cutting various
materials, curved sawing, flush cutting, deep cutting, etc.
Overdischarge protection
The battery 2 (Fig. 8) is protected by the safety system
against deep discharge. In case of complete discharge,
the power tool is automatically switched off.
Do not try to switch on the power tool
when the protection system is activated
the battery can be damaged.
Indicators of the state of battery charge (see Fig. 8)
With the push of the button 25 the indicators 26 show
the state of charge of the battery.
7. HOW TO CHARGE THE BATTERY
Battery charging time
Initial operating of the power tool
14
Before the first use, the battery must be fully charged.
Charging process
• Press the battery lock 10 and remove the battery 9
(see Fig. 2).
• Connect the charger 11 to the power supply (see Fig. 6).
• Insert battery into charger.
• Disconnect the charger from power supply after
charging.
• Remove the battery from the charger and mount
battery in the power tool (see Fig. 2).
Charger indicators (see Fig. 7)
Charger indicators 34 and 35 inform of the battery
charging process. Signals of the indicators 34 and 35
are shown on the label 33. (see Fig. 7).
• Fig. 7.1 - (The green indicator 35 is on, the battery is
not inserted in the charger) - the charger is connected
to the power network (ready for charging).
• Fig. 7.2 - (The green indicator 35 is blinking, the battery
is inserted in the charger) - the battery is being charged.
• Fig. 7.3 - (The green indicator 35 is on, the battery is
inserted in the charger) - the battery is fully charged.
• Fig. 7.4 - (The red indicator 34 is on, the battery is
inserted in the charger) - the charging process of the
battery is terminated due to inappropriate temperature.
When the temperature conditions are normal, the process
of charging will resume.
• Fig. 7.5 - (The red indicator 34 is blinking, the battery
is inserted in the charger) - the charging process of the
battery is terminated because of its failure. Replace the
faulty battery, its further use is prohibited.
In the process of charging the battery and the charger
become hot, it is a normal process.

8. TURNING ON THE MACHINE

8.1 Press the on / off lock button 4 (Fig. 4). By releasing
the pressure on it, the machine stops.
8.2 Variable speed control
Variable speed control is possible with the on / off
switch 4.
Higher pressure on the switch increases the speed.
8.3 Working with the reciprocating saw
Always hold the machine by its two handles with both
hands. Start the saw to reach its full speed.
Rest the saw blade 8 on the workpiece that you want
to saw.
Then slowly move the saw blade along the cutting line.
Use specific saw blades for the type of material to be cut.
9. FITTING THE SAW BLADE
Remove the battery from the power
tool before carrying out work on the
power tool.