Technical Data; Safety Instructions - Felisatti RF62/1500VE Bedienungsanleitung

TECHNICAL DATA

Milling machine
Absorbed power
No load speed
 of milling cutter attachment
 maximum of milling cutter
Machine weight (without accessories)
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILUSTRATIONS
DESCRIPTION (See figures)
A Micro-adjustment disc (Fig.1)
B Micro-adjustment knob (Fig.1)
C Speed adjustment (Fig.1)
D ON/OFF switch (Fig.1)
E Grips (Fig.1)
F Clip-carrier shaft (Fig.1)
G Clip fixing nut (Fig.1)
H Fixed base (Fig.1)
I 22 mm spanner (Fig.1)
J Access adjustment over the table height (Fig.2)
K Depth adjustment handle (Fig.2)
L Unscrew the access base on the table (Fig.2)
M Base plate (Fig.2)
N Spindle lock of shaft (Fig.2)
O Fixing lever (Fig.2)
P Locking button (Fig.2)
Q Access to the blocking of the rotation axis (Fig.2)
R Locking lever (Fig.2)
S Copier bushing (Fig.18) (optional accessory)
EQUIPMENT
- Clip, 1/2" and 1/4"
- Fixed spanner, 22 mm
- Operating instructions

- Safety instructions

- Warranty
SAFETY INSTRUCTIONS
 See "Safety instructions" enclosed manual, supplied
together with this instruction manual.
 WARNING! The dust produced when milling asbestos
and/or silica stone materials is dangerous to health.
Follow the insurance company's safety instructions
regarding the responsibility of employees.
 For your personal safety, always connect the machine
to a mains supply by a differential and thermal cut-out
switch, in accordance with regulations on low-voltage
wiring sitemaps.
 Do not perforate the machine casing, as this would
destroy the protective insulation (use adhesive labels).
W
rpm
mm
mm
kg
 Always unplug the machine before doing any work on it.
 Always stop the machine by switching it off, not by
unplugging it.
 WARNING! Before each use, inspect the plug and
lead. Should they need replacing, have this done by an
official service centre. Only plug the machine in when it
is switched off.
 Always keep the lead out of the machine's working
area.
 Only plug the machine in when it is switched off.
 Do not allow the machine to get wet, nor should it be
used in wet environments.
 When using the machine, always wear safety goggles,
gloves and non-slip footwear, and it is advisable to
wear ear protection.
 Check for correct piece fixing before commencing any
operation.
 Only milling heads with acceptable revolutions that are
at least the same as the maximum off-load revolutions
of the machine should be used.
 The milling head shaft diameter should match the
inside diameter of the tool-holder (locking clip).
 It should be ensured that the milling head is firmly held
in place before the machine is operated.
 The clip-carrier shaft support lever must only be oper-
ated when the machine is stopped.
 The milling head should only be brought into contact
with the work-piece after it has been switched on.
 The machine must be firmly held by the grips. Other-
wise the recoil produced could cause the machine to
work imprecisely or even dangerously.
 Hold the machine firmly in both hands and in a stable
position.
 During use, it should be ensured that the milling head
is in the centre of the copy bushing in order to prevent
any personal injury or damages to the work-piece.
 The milling machine must never be used on metal
objects, such as nails and screws.
 Hand must be kept clear of the milling machine while it
is operating.
 The cutting depth must never be adjusted with the
motor running. A mistake in this time could lead to
personal injury and/or damage to the milling head or
work-piece.
 The operator should remain alert and keep the milling
head apart from all objects during operation.
 When the milling operation has been completed,
locking lever should be operated so that the machine
returns to its upper starting position.
 The motor must be allowed to come to completely stop
before being put to one side between uses.
 The milling heads should be protected from impacts
and knocks.
RF62/1500VE
1500
12000-23000
12
60
2.450