Technical Data; Safety Instructions - Felisatti RF67/2200VE Bedienungsanleitung

TECHNICAL DATA

Milling machine
Absorbed power
No load speed
 of milling cutter attachment
Machine weight (without accessories)
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A Safety push button switch (Fig.2)
A1 On-/off switch (Fig.2)
B Blocking button of the clip-holder shaft (Fig.1)
C Depth adjustment handle (Fig.1)
D Clip fixing nut (Fig.1 and Fig.2)
E Depth stop (Fig.1)
F Stepped stop (Fig.1)
G Locking wing nut (Fig.1)
H Fixing lever (Fig.2)
I Side stop (Fig.3)
J Transparent frontal protection (Fig.5)
K Dust suction adapter (Fig.6)
L Speed adjustment (Fig.1)
M Fine depth stop adjustment (Fig.1)
N Depth adjustment handle (Fig.1)
O Grips (Fig.1)
P Base plate (Fig.6)
Q Sliding plate (Fig.2 and Fig.3)
R Wing screw for dust suction adapter (Fig.6)
S Strip stop (Fig.3)
T Parallel stop fine adjustment (Fig.3)
U Copier bushing (Fig.3)
V Wing screw (Fig.5 and Fig.6)
W Depth adjustment handle (Fig.2)
Y Depth adjustment scale (Fig.5)
EQUIPMENT
- Side stop
- Clip, 1/2" and 1/4"
- Fixed spanner, 22 mm and 7 mm
- Transparent guard
- Dust suction adapter
- Copier bushing
- Operating instructions

- Safety instructions

- Warranty
SAFETY INSTRUCTIONS
 See "Safety instructions" enclosed manual, supplied
together with this instruction manual.
W
rpm
mm
kg
 WARNING! The dust produced when milling asbestos
and/or silica stone materials is dangerous to health.
Follow the insurance company's safety instructions
regarding the responsibility of employees.
 For your personal safety, always connect the machine
to a mains supply by a differential and thermal cut-out
switch, in accordance with regulations on low-voltage
wiring sitemaps.
 Do not perforate the machine casing, as this would
destroy the protective insulation (use adhesive labels).
 Always unplug the machine before doing any work on it.
 Always stop the machine by switching it off, not by
unplugging it.
 WARNING! Before each use, inspect the plug and
lead. Should they need replacing, have this done by an
official service centre. Only plug the machine in when it
is switched off.
 Always keep the lead out of the machine's working
area.
 Only plug the machine in when it is switched off.
 Do not allow the machine to get wet, nor should it be
used in wet environments.
 When using the machine, always wear safety goggles,
gloves and non-slip footwear, and it is advisable to
wear ear protection.
 Check for correct piece fixing before commencing any
operation.
 Only milling heads with acceptable revolutions that are
at least the same as the maximum off-load revolutions
of the machine should be used.
 The milling head shaft diameter should match the
inside diameter of the tool-holder (locking clip).
 It should be ensured that the milling head is firmly held
in place before the machine is operated.
 The clip-carrier shaft support lever must only be oper-
ated when the machine is stopped.
 The milling head should only be brought into contact
with the work-piece after it has been switched on.
 The machine must be firmly held by the grips. Other-
wise the recoil produced could cause the machine to
work imprecisely or even dangerously.
 Hold the machine firmly in both hands and in a stable
position.
 During use, it should be ensured that the milling head
is in the centre of the copy bushing in order to prevent
any personal injury or damages to the work-piece.
 The milling machine must never be used on metal
objects, such as nails and screws.
 Hand must be kept clear of the milling machine while it
is operating.
 The cutting depth must never be adjusted with the
motor running. A mistake in this time could lead to
personal injury and/or damage to the milling head or
work-piece.
RF67/2200VE
2200
12000-21000
12
5.9