Technical Data; Brief Description - Felisatti RH24/700ER Bedienungsanleitung

Rotary hammer
Rated voltage
Rated frequency
Rated power
No load speed
No load hammer rate
Drilling diameter in concrete
Drilling diameter in steel
Drilling diameter in wood
Weight according EPTA-Procedure 01/2003
Read the operating instructions
Protection category II power tool; double
insulated
Wear eye, ear protection
Follow very carefully the instructions in this manual,
save it and keep it close at hand, ready to carry out any
inspection of parts that may be necessary.
If the tool is used with care and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought
shall be only those described in this manual. Any other
use of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A SDS-plus chuck (Fig.1)
B Chuck sliding ring (Fig.1)
C Speed regulating handwheel (Fig.1)
D Push button for mode change (Fig.1)
E Mode changeover(Fig.1)
F Label for reversing rotation R-L (Fig.1)
G Changeover left/right direction switch (Fig.1)
H On-/off switch (Fig.1)
I Locking button (Fig.1)
K Depth stop fixing wing nut (Fig.1)
L Depth gauge (Fig.1)
M Auxiliary handle (Fig.1)
N Screwdriver bit (accessory*) (Fig.2)
O Key chuck (accessory*) (Fig.2)
P SDS-plus adapter (accessory*) (Fig.2)
* Not included in standard equipment, available as an
accessory

BRIEF DESCRIPTION

A percussion unit generates the power necessary for
hammer drilling or chiselling in masonry.
Just like when we hit a conventional chisel with
hammer, a free piston strikes the bit or chisel, which can
move lengthways, through an intermediate part. This free

TECHNICAL DATA

V~
Hz
W
/min
min
mm
mm
mm
kg
piston is driven by a second piston activated by an electric
motor through an air cushion. This electro-pneumatic
principle offers great percussion elasticity and work free
from recoil.
Unlike a normal hammer drill, the drilling capacity
does not depend on the pressure exerted on the machine.
Use of the tool: The rotary hammer can be used
for hammer drilling and drilling in wood, metal as well as
plastic, and also for driving screws with driving bits installed
in a key chuck with the SDS-plus adapter. Any other use
not mentioned is not allowed.
Additional features of the rotary hammer:
- The machine is equipped with a safety clutch or
mechanism which operates when a bit seizes up, pro-
tecting the user and the machine's electro-mechanical
parts. The clutch is released automatically.
WARNING! This machine must not be used with hole
saws, core bits, diamond bits, etc, as they tend to jam in
the hole easily. This would cause the safety clutch to trip
out too often.
- Percussion drill chuck A with SDS–plus mounting for
using tools with SDS-plus shaft. A geared drill chuck or a
keyless chuck can be used in conjunction with the SDS-
Plus Adapter P.
Change direction of rotation with switch lever G –due
-
to a lockout mechanism, switching the lever is only possi-
ble if the On/Off switch H is not depressed.
- Electronic control of spindle speed, infinitely variable
by finger pressure on the On/Off switch H.
- For maximum speed regulation use handwheel C.
- For continuous operation the On/Off switch can be
locked in the "On" position by the button I.
Auxiliary handle M, adjustable, with integral depth
-
gauge L.
BEFORE USING THIS TOOL
WARNING! Before carrying out any work, check, for
instance, using a metal detector, that there are no electric
wires or gas or water pipes under the surfaces you wish to
work on.
Make sure the mains voltage is correct: it must be
the same as that on the specification label. Machines with
230V can also be connected to a 220V mains supply.
To turn the machine on, press the ON/OFF switch H
and keep it pressed down.
When the ON/OFF switch is released, the machine
RH24/700ER RH30/900ER
230
50
720
0-1240
0-5080
24
13
24
2.9
900
0-1050
0-5100
30
13
30
3.3
5