Technical Data; Brief Description - Felisatti RH45/1100VE Bedienungsanleitung

Rotary hammer
Rated voltage, V~
Rated frequency, Hz
Rated power, W
No load speed, /min
No load hammer rate, /min
Nominal impact energy, J
Drilling diameter in concrete,mm
Weight according EPTA-Procedure 01/2003, kg
Read the instruction manual completely and
carefully before using the power tool.
Protection category II power tool; double
insulated
In accordance with essential applicable safety
standards of European directives
Wear eye, ear protection
Follow very carefully the instructions in this manual,
save it and keep close at hand, ready to carry out any
inspection of parts that may be necessary.
If the machine is used carefully and normal
maintenance is carried out, it will work well for a long time.
The functions and use of the tool you have bought
shall be only those described in this manual. Any other
use of the tool is strictly forbidden.
ILLUSTRATIONS
The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Dust protection cap
2 Chuck sliding ring
3 Mode changeover
4 On-/off switch
5 Speed regulating handwheel
6 Auxiliary handle
7 Principal hand grip
EQUIPMENT
- Auxiliary handle
- Plastic case
- Operating instructions with Safety instructions
- Warranty

BRIEF DESCRIPTION

A percussion unit generates the power necessary for
hammer drilling or chiselling in masonry.
Just like when we hit a conventional chisel with
hammer, a free piston strikes the bit or chisel, which can
move lengthways, through an intermediate part. This free
piston is driven by a second piston activated by an electric
motor through an air cushion. This electro-pneumatic

TECHNICAL DATA

V~
Hz
W
/min
min
J
mm
kg
principle offers great percussion elasticity and work free
from recoil.
Any other use not mentioned is not allowed.
Additional features of the rotary hammer:
- The machine is equipped with a safety clutch or
mechanism which operates when a bit seizes up, protecting
the user and the machine's electro-mechanical parts. The
clutch is released automatically.
- For maximum speed regulation use handwheel 5.
- Auxiliary handle 6, adjustable, with integral depth
gauge.
BEFORE USING THIS TOOL
WARNING! Before carrying out any work, check, for
instance, using a metal detector, that there are no electric
wires or gas or water pipes under the surfaces you wish to
work on.
Make sure the mains voltage is correct: it must be
the same as that on the specification label. Machines with
230V can also be connected to a 220-V mains supply.
To turn the machine on, press the ON/OFF switch 4
and keep it pressed down.
When the ON/OFF switch is released, the machine
stops.
WARNING! Always disconnect the plug from the
socket before doing any work on the machine.
1. Fitting the working tools (Fig.1, 2)
Only use tools with SDS-max shaft!
1. Clean and grease the shaft of the tool.
2. Insert the tool in a twisting manner into the tool holder
until it latches itself.
3. Check that the tool is properly locked into place. It
must be possible to move it about 10 mm lengthways.
4. Switch machine over to hammer drilling with lever 3 in
appropriate position.
2.Removal tools
Push back the locking sleeve 2 and remove the tool.
3. Changing the position of the auxiliary handle
1. Unscrew the auxiliary handle 6 in an anticlockwise
direction.
2. Turn the auxiliary handle 6 to the required position.
3. Screw the auxiliary handle 6 in place again.
4. Setting the depth gauge
Make sure before you start that drill-bit is inserted in
the
SDS-max chuck.
1. Slightly loosen the fixing wing nut .
2. Hold the bit tip against the work surface. Push the
RH45/1100VE RH50/1200VE
230
50
1100
130-370
1990-3200
0-10
45
7
1200
0-14
52
7,6
5