LIGHTING
After the first ignition you can smell bad odours (owing to the drying of the glue used in the garnitures or of the paint) which disappear after
a brief using of the appliance. A good ventilation of the room should always be guaranteed.
To lighT The fire, iT is suggesTed To use smAll wood pieces TogeTher wiTh pAper or oTher TrAded lighTing
meAns. IT Is FORBIDDEN TO usE aNy LIquID suBsTaNcE as FOR Ex. aLcOHOL, GasOLINE, OIL aND sImILaR.
open the primary air completely.
when wood starts to burn, it is possible to feed it again by opening slowly the door, in order to avoid leaks of smoke, and close the primary
air register and control the combustion through the secondary air register according to the provisions of chapter TechnicAl descripTion.
PLEasE aLways BE PREsENT DuRING THIs PHasE.
NEvER OvERLOaD THE aPPLIaNcE (see cap. TechnicAl descripTion - hourly consumpTion).
TOO mucH FuEL aND TOO mucH aIR FOR cOmBusTION caN causE OvERHEaTING aND THEREFORE DamaGE THE
samE. NEvER swITcH ON THE DEvIcE wHEN THERE aRE cOmBusTIBLE GasEs IN THE ROOm.
To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to know the following information:
• the construction materials of the involved products are not homogeneous, in fact there are simultaneously parts in cast iron, steel,
refractory material and majolica;
• the temperature to which the body of the product is subject is not homogeneous: from area to area, variable temperatures within the
range of 300°c - 500°c are detected;
• during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to cycles of intense use or
of absolute standstill when season changes;
• the new appliance, before being considered seasoned has to be subject to many start cycles to allow all materials and paints to complete
the various elastic stresses;
• in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress, as well as of wet paint.
Therefore, it is extremely relevant to take these easy steps during the lighting:
1. make sure that a strong air change is assured in the room where the appliance is installed.
2. during the first starts, do not load excessively the combustion chamber (about half the quantity indicated in the instructions manual) and
keep the product continuously on for at least 6-10 hours with the registers less open than the value indicated in the instructions manual.
3. repeat this operation for at least 4-5 or more times, according to your possibilities.
4. Then load more and more fuel (following in any case the provisions contained in the installation booklet concerning maximum load) and,
if possible, keep the lighting periods long avoiding, at least in this initial phase, short on/off cycles.
5. DuRING THE FIRsT sTaRTs, NO OBjEcT sHOuLD BE LEaNED ON THE aPPLIaNcE aND IN DETaIL ON ENamELLED suRFacEs.
ENamELLED suRFacEs musT NOT BE TOucHED DuRING HEaTING.
6. once the «break-in» has been completed, it is possible to use the product as the motor of a car, avoiding abrupt heating with excessive
loads.
aFTER TEsTING THE PROPER wORkING OF THE aPPLIaNcE, sOmE Days FROm THE INsTaLLaTION, IT Is POssIBLE TO
PROcEED wITH THE cONsTRucTION OF ITs aEsTHETIc cOvERING.
waRNING: during The surround building operATions iT musT kepT in mind possible And subsequenT elecTricAl
insTAlled pArTs mAinTenAnce (fAns, TemperATure probe, eTc) And wiTh hydrAulic sysTems All pArTs connecTed
To The Thermo-fireplAce.
LOw EmIssION FIRE LIGHTING
smokeless combustion is a way of lighting a fire able to significantly reduce the emission of harmful substances. The wood burns gradually
from the top downwards, so combustion is slower and more controlled. burnt gases pass through the high temperatures of the flame and
therefore burn almost completely.
place the logs in the hearth a certain distance apart as shown in the
or vertically in the case of tall narrow combustion chambers. place the fire starter module on top of the pile, arranging the first logs in the
module at right angles to the pile of wood.
FIRE sTaRTER mODuLE. This fire sTArTer module replAces A pAper or cArdboArd sTArTer.
prepare four logs, 20 cm long with a cross section of 3 cm by 3 cm
right angles, with the fire lighter (wax impregnated wood fibre for example) in the middle. The fire can be lit with a match.
if you want, you can use thinner pieces of wood. in this case, you will need a larger quantity.
keep the flue gas exhaust valve and combustion air regulator open (1a - 2a). After lighting the fire, leave the combustion air regulator open
in the position shown in the picture.
ImPORTaNT:
•
do not add further wood between one complete load and the next;
•
do not suffocate the fire by closing the air intakes;
•
regular cleaning by a chimney sweep reduces fine particle emissions.
These instructions are backed by ENERGIA Legno SVIZZERA
Picture 9.
Arrange the largest at the bottom and the smallest at the top,
Picture
9. cross the four logs and place them on top of the pile of wood at
www.energia-legno.ch
ENGLISH
31