Installation; Operation - Conrad 75 50 04 Bedienungsanleitung

O P E R A T I N G I N S T R U C T I O N S
Electronic safe 20
Item no. 75 50 04
Intended use
The safe can be used to store valuables. It has a stable steel casing and can be fi rmly attached
to a wall or placed on a stable surface.
It is operated with 4 batteries of type AA/Mignon The safe can also be opened with the keys
enclosed when the batteries are fl at.
Follow the safety instructions and all other information in this operation manual.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Contents
• Safe
• Two keys
• 4 screws and 4 washers
• Operating Instructions
Explanation of the Symbols
This symbol indicates specifi c risks associated with handling, function and use.
☞
The "Hand" symbol indicates special tips and operating information.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! In such cases,
the warranty will be null and void.
• The unauthorised conversion and/or modifi cation of the product is not allowed for
safety and approval reasons (CE).
• The product is approved only for mounting and operation in dry, closed rooms. No
part of the product must be allowed to get damp or wet.
• The product is not a toy and should be kept out of the reach of children!
• Do not leave packing materials unattended. They may become dangerous play-
things for children.
Battery Notes
• Batteries should be kept out of the reach of children.
• Do not leave batteries lying around in the open; there is a risk of them being swallowed by
children or domestic animals. If swallowed, consult a doctor immediately.
• Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suitable
protective gloves.
• Batteries/rechargeable batteries must not be short-circuited, opened or thrown into a fi re.
There is a risk of explosion!
• Do not recharge normal, non-rechargeable batteries, risk of explosion!
• Do not mix batteries with different charges (e.g. fl at and half-discharged batteries).
☞
Due to safety reasons and operating duration, only high-quality alkaline batteries
should be used and not rechargeable batteries.

Installation

Select a place for installation where the safe is not immediately visible or easily accessible. This
may be behind a closet door or behind books, folders, or similar.
Installation in a partition wall (hollow wall) would also be ideal; a picture may be hung up in
front of the door.
☞
www.conrad.com
The safe can be mounted to a wall as well as on the fl oor, or another stable surface, using the
holes in the housing.
Version 02/12
☞
Suitable screws and screw plugs may be necessary for installation depending on the surface.
Additional fi xation with special clue or similar is possible, if the surface is suitable.
Opening/closing the safe with the key
☞
• Remove the round, thin plastic cover from the lock; it is
situated directly to the right of the closing handle.
• Insert the key into the lock observing the correct orien-
tation and turn the key a little to the left in anti-clockwise
direction.
Hold the key in this position and turn the closing handle
to the right until it stops. Take the key out of the lock and
open the safe door.
• To close the safe, shut the safe door fi rst. Then, turn
the closing handle to the left until it stops; the lock is
engaged.
Check the lock; you should not be able to turn the closing handle to the right.
☞
Inserting/Replacing Batteries
• Open the safe using the keys as described above.
• Open the battery case at the back of the door; to do this, slide the cover backwards until it can
be removed.
• Insert four new „AA/mignon" batteries with the correct polarity (observe +/Plus and -/Minus).
• Close the battery compartment again.
• Replacing the batteries is necessary, when the red LED light up when opening the safe or
the safe cannot be opened when entering the code. The access code is maintained when
replacing the batteries.
☞

Operation

Opening the safe by entering the code
• Enter the code and then press either the asterisk or the hash key. A beep will be heard every
time a key is pressed.
☞
• When the code is correct, the green LED will light up and two beeps will be heard.
Turn the closing handle to the right until it stops within 5 seconds and open the door. If the
closing handle is not moved, the lock closes automatically after 5 seconds due to safety
reasons.
• If the code is incorrect, 3 beeps will be heard. After entering the wrong code three times, the
number pad is locked for 20 seconds. If a wrong code is entered three times once again, the
number pad is locked for 5 minutes.
• To close the safe, shut the safe door fi rst. Then, turn the closing handle to the left until it stops;
the lock is engaged.
Check the lock; you should not be able to turn the closing handle to the right.
☞
Protect the safe from dampness and humidity. Thus, do not install the safe in rooms
with high humidity or damp basements.
If the safe is locked upon delivery, use the keys enclosed to open it.
The corresponding lock is hidden behind a small, thin plastic cover, which is situated
directly right to the closing handle.
This may be necessary when the batteries are half-fl at or fl at so that the safe cannot
be opened by entering the access code. The safe can be used in this way without
batteries, if desired.
If you accidentally turn the closing handle to the left when the safe door ist open
so that both lock bolts reach out of the safe door (the safe cannot be closed now),
simply proceed as described above.
If the safe does not respond to entries on the number pad, it can also be opened
using the keys enclosed. The corresponding lock is situated under a thin plastic
cover right to the closing handle, see image above.
The default setting for the code is "159".
If you accidentally turn the closing handle to the left when the safe door ist open
so that both lock bolts reach out of the safe door (the safe cannot be closed now),
simply proceed as described above.