Werbung
TECHNICAL DATA
CORDLESS NAILER
Production code...............................................................................................
Collation angle .................................................................................................
Fastener type: brad
Diameter.......................................................................................................
Length min./max...........................................................................................
Magazine capacity (number of nails) ...............................................................
Cycle rate ........................................................................................................
Battery voltage.................................................................................................
Weight according EPTA-Procedure 01/2014 (2.0 Ah ... 12.0 Ah) ....................
Recommended ambient operating temperature ..............................................
Recommended battery types...........................................................................
Recommended charger ...................................................................................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ................................................
Sound power level (Uncertainty K=3dB(A)) .....................................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according
to EN 60 745.
Vibration emission value a
.........................................................................
h
Uncertainty K= .............................................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent applications,
with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and noise such as: maintain the tool and the accessories,
keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions, illustrations
and specifi cations provided with this power tool. Failure to follow
all instructions listed below may result in electric shock, fi re and/or
serious injury.
Save all warnings and instructions for future reference.
CORDLESS NAILER SAFETY WARNINGS
Always assume that the tool contains fasteners. Careless handling
of the nailer can result in unexpected fi ring of fasteners and personal
injury.
Do not point the tool towards yourself or anyone nearby.
Unexpected triggering will discharge the fastener causing an injury.
Do not actuate the tool unless the tool is placed fi rmly against the
workpiece. If the tool is not in contact with the workpiece, the fastener
may be defl ected away from your target.
Disconnect the tool from the power source when the fastener
jams in the tool. While removing a jammed fastener, the nailer may
be accidentally activated if it is plugged in.
Use caution while removing a jammed fastener. The mechanism
may be under compression and the fastener may be forcefully
discharged while attempting to free a jammed condition.
Do not use this nailer for fastening electrical cables. It is not
designed for electric cable installation and may damage the insulation
of electric cables thereby causing electric shock or fi re hazards.
Wear ear protectors. Exposure to noise can cause hearing loss.
Hold power tool by insulated gripping surfaces, when performing
an operation where the nail may contact hidden wiring. Nails
contacting a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Always wear eye protection with side shields. Everyday glasses
have only impact resistant lenses. They are not safety glasses.
Following this rule will reduce the risk of serious personal injury.
Eye protection provides protection against flying particles both
from the FRONT and SIDE should ALWAYS be worn by the
operator and others in the work area when loading, operating or
22
ENGLISH
M18 FN18GS
.........4741 26 02
...000001-999999
................. 0 °
.............. 1,2 mm
.......... 16/54 mm
............. 110
............. 900 /h
............... 18 V
2,9 kg ... 4,0 kg
... -18°C ... +50 °C
.. M18B...M18HB...
M12-18 C...M1418 C6
............ 81,1 dB (A)
............ 92,1 dB (A)
............ 1,97 m/s
2
.............. 1,5 m/s
2
servicing this tool. Eye protection is required to guard against flying
fasteners and debris, which could cause severe eye injury.
Always remove the battery before adjusting the depth of drive wheel.
Do not pull back on the adjustment wheel, the wheel is designed to be
rotated.
Do not press the trigger while adjusting the depth of drive wheel.
Always select full sequential fi ring mode before adjusting the depth of
drive.
Do not point the tool towards yourself or anyone nearby when
adjusting the depth of drive.
ADDITIONAL SAFETY INSTRUCTIONS
Always be aware that misuse and improper handling of this tool can
cause injury to yourself and others.
The tool is designed for single-hand use. Do not hold the tool by the
front of the magazine. Do not put hands, head, or other parts of your
body near the bottom of the magazine where the nail exits the tool, as
serious personal injury could be caused.
Always ensure that the workpiece contact is fully positioned above the
workpiece. Positioning the workpiece contact only partially above the
workpiece could cause the nail to miss the workpiece completely and
result in serious personal injury.
Do not drive nails near edge of material. The workpiece may split
causing the nail to ricochet, injuring you or a coworker. Be aware that
the nail may follow the grain of the wood, causing it to protrude
unexpectedly from the side of the work material or defl ect, possibly
causing injury.
Keep hands and body parts clear of immediate work area. Hold
workpiece with clamps when necessary to keep hands and body out of
potential harm. Be sure the workpiece is properly secured before
pressing the fastener against the material. The workpiece contact may
cause the work material to shift unexpectedly. Keep face and body
parts away from back of the tool cap when working in restricted areas.
Sudden recoil can result in impact to the body, especially when nailing
into hard or dense material.
During normal use the tool will recoil immediately after driving a
fastener. This is a normal function of the tool. Do not attempt to prevent
the recoil by holding the nailer against the work. Restriction to the
recoil can result in a second fastener being driven from the nailer. Grip
the handle fi rmly, let the tool do the work and do not place second
hand on top of tool or near exhaust at any time. Failure to heed this
warning can result in serious personal injury.
Do not drive fasteners on top of other fasteners or with the tool at an
overly steep angle as this may cause defl ection of fasteners which
could cause injury.
Always check the work area for hidden wiring, gas lines, water lines,
etc., before using the product on such work area.
After using the product in the contact actuation mode, switch it back to
the full sequential mode.
The driving depth of the nail may be adjusted beyond air pressure. It is
advisable to test the depth on a scrap workpiece to determine the
required depth for the application.
Only fasteners matching the description in the Technical Data can be
used with this tool. Using incorrect fasteners may lead to jamming or
other malfunctions.
Do not select contact actuation mode when working on scaff olds,
ladders or platforms where you may need to move your body position.
You may unintentionally fi re a nail by inadvertent activation of the
workpiece contact while moving about if the contact actuation mode is
selected. When moving positions, select full sequential activation or
deactivate the product completely by removing the battery pack. This
will reduce the potential for injury to yourself and others.
Do not dispose of used battery packs in the household refuse or by
burning them. Milwaukee Distributors off er to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short circuit
risk).
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Use only 18 V chargers for charging 18 V battery packs. Do not use
battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery pack or
charger in fl uid or allow a fl uid to fl ow inside them. Corrosive or
conductive fl uids, such as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The nailer is intended for driving nails into wood or similar soft
materials from a magazine containing a strip of suitable nails. The nails
which can be safely loaded into the magazine for the product are
described in the product specifi cation table in this manual. Do not use
any other type of nail or fi xing with the nailer. Do not operate in contact
actuation mode while working on scaff old, ladder or other platform
where a change in working position is required. Use only full sequential
mode in this case. The nailer should not be used for fi xing electric
cables.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under "Technical Data" fulfi lls all the relevant provisions of the
directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC and the
following harmonized standards have been used:
EN 60745-1:2009+A11:2010
EN 60745-2-16:2010
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-10-29
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the
product described under "Technical Data" fulfi lls all the relevant
provisions of the following Regulations S.I. 2008/1597 (as amended),
S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and that
the following designated standards have been used:
BS EN 60745-1:2009+A11:2010
BS EN 60745-2-16:2010
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2020-10-29
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess removeof 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure to heat or
sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be fully
charged.
To obtain the longest possible battery life remove the battery pack from
the charger once it is fully charged.
"For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away
from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
ENGLISH
23
Werbung
