Technical Data - Milwaukee M18 FFN Originalbetriebsanleitung

TECHNICAL DATA

Production code...........................................................................
Collation angle .............................................................................
Fastener type: brad
Diameter ...................................................................................
Length min./max. ......................................................................
Magazine capacity (number of nails) ...........................................
Cycle rate ....................................................................................
Battery voltage.............................................................................
Weight according EPTA-Procedure 01/2014 (2.0 Ah ... 12.0 Ah)
Recommended ambient operating temperature ..........................
Recommended battery types.......................................................
Recommended charger ...............................................................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ............................
Sound power level (Uncertainty K=3dB(A)) .................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 60 745.
Vibration emission value a
Uncertainty K= ..........................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may
signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power
tool. Failure to follow all instructions listed below may result
in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
CORDLESS NAILER SAFETY WARNINGS
Always assume that the tool contains fasteners.
Careless handling of the nailer can result in unexpected
fi ring of fasteners and personal injury.
Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the fastener
causing an injury.
Do not actuate the tool unless the tool is placed fi rmly
against the workpiece. If the tool is not in contact with the
workpiece, the fastener may be defl ected away from your
target.
Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the nailer may be accidentally activated if it is
plugged in.
Use caution while removing a jammed fastener. The
mechanism may be under compression and the fastener
may be forcefully discharged while attempting to free a
jammed condition.
Do not use this nailer for fastening electrical cables. It is
not designed for electric cable installation and may damage
28 ENGLISH
470 200 - M18FFN.indd 28 470 200 - M18FFN.indd 28
CORDLESS NAILER
......................................................
h
M18 FFN
.......................4741 16 01
...000001-999999
...........................30 °
................2,9 - 3,32 mm
......................50/90 mm
...........................51
.............................3 /sec
...........................18 V
........... 4,7 kg ... 5,8 kg
................... -18°C ... +50 °C
.................. M18B...M18HB...
.............. M12-18 C...M1418 C6
........................90,1 dB (A)
......................101,1 dB (A)
..........................5,9 m/s
2
..........................1,5 m/s
2
the insulation of electric cables thereby causing electric
shock or fi re hazards.
Wear ear protectors. Exposure to noise can cause hearing
loss.
Hold power tool by insulated gripping surfaces, when
performing an operation where the nail may contact
hidden wiring. Nails contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock.
Always wear eye protection with side shields. Everyday
glasses have only impact resistant lenses. They are not
safety glasses. Following this rule will reduce the risk of
serious personal injury.
Eye protection provides protection against flying
particles both from the FRONT and SIDE should
ALWAYS be worn by the operator and others in the work
area when loading, operating or servicing this tool. Eye
protection is required to guard against flying fasteners and
debris, which could cause severe eye injury.
Always remove the battery before adjusting the depth of
drive wheel.
Do not pull back on the adjustment wheel, the wheel is
designed to be rotated.
Do not press the trigger while adjusting the depth of drive
wheel.
Always select full sequential fi ring mode before adjusting the
depth of drive.
Do not point the tool towards yourself or anyone nearby
when adjusting the depth of drive.
13.05.2020 10:41:51 13.05.2020 10:41:51