UNILITE BLT-1 Bedienungsanleitung

FEATURES
• 250 Lumen 6500k white COB LEDs
• With Red 625nm static & flashing modes
• 2 - 30 hours runtime
• Light is easily removed from hat
• Built-in USB-A connector with protective cover
• Directly charged via a USB port
• High quality 3.7v 420mAh li-po battery
• Super fast charge time - 1.5 hours
• IPX5 water resistant
• Comfortable knitted Beanie, one size fits all
• Fabric: 35% acrylic 65% polyester
• Machine washable at 30°C
BATTERY - 3.7v 420mAh Li-polymer Battery
WEIGHT - 27g (light only)
DIMENSIONS - 73.5 x 41 x 15mm
ADVICE & IMPORTANT INFORMATION!
Do not look directly at LEDs. Do not operate in intense sunlight or extreme
temperature conditions (below -10°C or above 40°C).
LEDs can become warm/hot when switched on; do not touch and never place
LEDs face down on any surface – risk of fire!
Do not use the device if there is any visible damage to the housing, lens, USB
connector or switch. Take care when using a USB plug adaptor, check for any
damage. DO NOT exceed 5V 1A charging input or damage may occur to the
internal rechargeable battery.
The rechargeable battery will reach full performance after a few complete charging
and discharging cycles.
To keep the rechargeable battery in optimum condition, it shovuld be recharged
every 3-6 months, especially if it is not being used for a long period of time. Always
fully charge rechargeable batteries before storage.
Always protect batteries from heat, intense sunlight, fire, water and moisture –
danger of explosion!
If a battery is damaged, fluids can leak out. AVOID contact as this can lead to
skin irritation and/or burns. If skin contact occurs, rinse thoroughly with water.
If irritation persists, seek medical advice. Seek immediate medical assistance if
battery fluid comes into contact with the eyes.
www.unilite.co.uk
ANSI FL 1 Standard
White - High
White - Low
Red - High
Red - Flash
OPERATION
Switch Sequence: WHITE HIGH > WHITE LOW > RED HIGH > RED
FLASH > OFF
(If left in any mode for over 3 seconds, next press will turn OFF)
ON/OFF
switch
CHARGING
1. Max charging input is 5V 1A.
2. Remove the rubber cover from the end.
3. Plug the USB-A connector directly into a USB charging port
(do not exceed 5V 1A input or damage may occur).
4. Red LED indicates charging, green LED indicates fully charged.
5. Charge Time: 1 ½ hrs
**Warranty void if max charging input is exceeded**
Children under 12 years of age should only use the product under adult
supervision.
Do not open, disassemble or attempt to modify the product; this will void the
warranty and can be dangerous. Improper use or modification is not covered
under the warranty.
Take care not to let lenses come into contact with hard/sharp objects, damage/
scratches to lenses will affect light output.
This product is water resistant to IPX5 – DO NOT SUBMERGE. If the product has
been subjected to excessive moisture/water the warranty may be void.
This product has a 1 year standard warranty (or extended 2 years once registered
online at WWW.UNILITE.CO.UK/WARRANTY) against manufacturing faults and
defects. It does not cover normal wear and tear, modifications, accidental damage
or poor maintenance. Unilite warranties do not cover battery leaks or the use of
incorrect chargers and cables that can damage rechargeable batteries.
Do not dispose of this device in normal household waste. It must be disposed
of via an authorised electrical appliance disposal centre or at your local waste
disposal unit.
Please re-use or recycle packaging where possible.
Keep these instructions for future reference or for subsequent possessors.
BLT-1
250
13 M 2 H
Lumen
70
7 M 3½ H
Lumen
15
-- 4 H
Lumen
15
-- 30 H
Lumen
CHARGING INDICATOR
Red = Charging
Green = Fully Charged