Specifications - Anker MagGo 633 Bedienungsanleitung

Le présent appareil est conforme aux CNR d' Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A25A7 is in compliance with
Directives 2014/53/EU & 2014/30/EU & 2011/65/EU. The full text of the EU declaration of
conformity is available at the following internet address:
https://www.anker.com/
This symbol indicates that this product shall not be treated as household waste. Instead
it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment.
GB Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A25A7 is in compliance with
Electromagnetic Compatibility Regulations 2016, Radio Equipment Regulations 2017 and The
Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2012 Electrical Equipment (Safety) Regulations 2016 & The Ecodesign for Energy-
Related Products Regulations 2010.. The full text of the GB declaration of conformity is available
at the following internet address:
https://www.anker.com
This device was tested for typical body-worn operations. To comply with RF exposure
requirements, a minimum separation distance of 20mm must be maintained between
the user's body and the handset, including the antenna. Third-party belt-clips, holsters,
and similar accessories used by this device should not contain any metallic components.
Body-worn accessories that do not meet these requirements may not comply with RF
exposure requirements and should be avoided. Use only the supplied or an approved
antenna.
This device is in compliance with the essential requirements and other relevant provisions
of UKCA. All essential radio test suites have been carried out.
This device was tested for typical body-worn operations. To comply with RF exposure
requirements, a minimum separation distance of 20cm must be maintained between
the user's body and the handset, including the antenna. Third-party belt-clips, holsters,
and similar accessories used by this device should not contain any metallic components.
Body-worn accessories that do not meet these requirements may not comply with RF
exposure requirements and should be avoided. Use only the supplied or an approved
antenna.
This device in compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU. All essential radio test suites have been carried out
1. The device complies with RF specifications when the device used at 20cm form your body
05

Specifications

Cell Capacity 5,000mAh
Portable Charger Input:
USB-C: 5V 2.4A / 9V 2.33A
Pogo Pin: 9V 2.33A
Output:
USB-C: 12W Max
Wireless: 5W / 7.5W
Charging Base Input:
USB-C: 9V 2.8A
Output:
Wireless earbuds: 5W Max
Pogo Pin: 21W Max
Wall Charger Input:
100-240V 1A 50/60Hz
Output:
5V 3A / 9V 2.8A
PPS 3.3-5.9V 3A / 3.3-11V 2.25A
Anker Innovations Limited
Room 1324-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3, 80807 Munich, Germany
Anker Technology (UK) Ltd
Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom
06