AJ 31114 Gebrauchsanleitung Seite 123

ATTENTION!
1. Environmentally hazardous waste, such as batteries and electronics, will have
a negative effect on the environment, or health, if handled incorrectly.
2. The waste packages should be sorted and put into solid dustbins according
to the materials and be collected disposal by local special environment
protection bureau. To avoid pollution, it's forbidden to throw away the wastes
randomly.
3. To avoid leaking during the use of the products, the user should prepare some
absorbable materials (scraps of wooden or dry duster cloth) to absorb the
leaking oil in time. To avoid second pollution to the environment, the used
absorbable materials should be handed in to special departments in terms of
local authorities.
NOTE!
All of the information reported herein is based on data available at the moment of
printing. We reserve the right to modify our own products at any moment without
notice and incurring in any sanction. So, it is suggested to always verify possible
updates.
Welcome to use our electrical lift table.This lift table is made of high quality steel
and is designed to give a durable, reliable and easy to use. For your safety and
correct operation, please carefully read this instruction and warnings on the lift
table before using it.
1. SPECIFICATIONS
Capacity
Lifting height
Min.height
Dimension of the table
Lifting speed
Lower speed
Pump electric current
Oil tank
Pump station
Weight
2. SAFETY GUIDANCE
2.1 Operator should read all warning signs on the truck and instructions here
before using it.
2.2 Do not put foot and hand under the scissors, injury could happen.
2.3 Do not enter under table.
2.4 Do not overload.
2.5 Do not use it on slope, lift table may become uncontrollable and creat
danger.
2.6 Do not lift persons. People could fall down and suffer severe injury.
2.7 Do not side or end load .Load must be distributed on at least 80% of the
table area.
2.8 The table should be maintained by the professional operator
2.9 Keep watching the condition of load, stop operating lift table if load becomes
unstable.
2.10 Check and maintain the lift table regularly.
2.11 Do not use the lift table continuously, the pump station would be damaged.
2.12 Stop operating the lift table if the temperature of the oil is too high.
2.13 The table should be lowered to the bottom if the lift table is not used.
3. CONTROL PANEL
Four switches
3.1 Emergency switch
When you press down this switch, it will switch off the power, and then you turn it
clockwise, it will switch on the power.
3.2 Lifting switch
When you press down this switch, the table will lift; when you loose your hand,
the table will stop lifting.
3.3 Lowering switch
When you press down this switch, the table will be lowering; when you loose
your hand, the table will stop lowering.
3.4 Replacement switch
The table can not lift or lower when the switch of safety protection frame starts.
When you press down the Lifting switch, the table will be lifting, press down this
switch the table will be lowering.
1000 kg
840 mm
80~85 mm
1450 x 1140 mm
18 s
15 s
3 l/min
3 l
AC3 x 380V, 750W
250 kg
2 | 01-2811700 • ajproducts.ie
4. MAINTENCE
4.1 Hydraulic oil
Please check the oil level every six months. The oil can be hydraulic oil: ISO VG
32 (GB11118-89), its viscosity should be 32cSt at 40°C, total volume is about
4.Olt.
4.2 Daily check and maintenance
It is necessary to check daily. Special attention should be paid to the rollers,
the axles, as thread,rags,etc.,it may block the rollers; the scissors and the table
should be checked, they may be deformed; the forks should be unloaded and
lowered in the lowest position when the job is over.
4.3 Lubrication
Use motor oil or grease to lubricate all movable parts.
5. TROUBLES SHOOTING
No. TROUBLE CAUSE
The table can not be -The hydraulic oil is
1
up the Max. height not enough.
-The position of the
travel switch.
2 The table can not lift -Without hydraulic
oil.
-Electromagnetic
valve can not work.
The motor can not -The emergency
3
run switch is turned off.
-The connection
of electrical wire is
loose.
-The contactor of DC
motor is damaged.
4 The table can not -The piston rod or
descend. mast is deformed
resulting from partial
loading slanting to
one side or over-
loading.
-The table was kept
in the high position
for long time, which
cause piston rod
bared to arise in rust-
ing and jamming of
the rod.
-The release valve of
pump cannot work
because of abrasion.
5 Leaks -Sealing parts worn
or damaged.
-Some parts
cracked.
6 The table descends -The impurities in the
without the release oil cause the release
valve worked valve to be unable to
close tight.
-Sealing parts worn
or damaged.
-The release valve is
damaged.
NOTE! DO NOT ATTEMPT TO REPAIR THE TRUCK UNLESS
YOU ARE TRAINED AND AUTHORIZED.
FIXING METHODS
-Pour in the oil.
-Adjust the position
of travel switch.
-Pour in the oil.
-Change the electro-
magnetic valve.
-Turn the emergency
switch clockwise.
-Tight it.
-Replace it with a
new one.
-Replace with new
one
-Keep the tablein the
lowest position if not
using, and pay more
attention to lubricate
the piston rod.
-Replace with new
one.
- Replace with new
one.
- Replace with new
one.
- Replace with new
one.
- Replace with new
one.
- Replace with new
one.