Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Read this manual carefully before using this product and check whether there are any
damaged parts. The product cannot be installed in case of damages. Keep this manual for
further reference.
SAFETY WARNINGS:
a) Keep this product out of reach of children and unauthorized users.
b)
Before using the device, make sure that all screws have been tightened.
c) This unit can become extremely hot whilst in operation; do not touch until it has had time
to cool down.
d) When the light bulb is burning or not completely cooled down, please do not touch it.
e) Mark sure there is adequate ventilation to aid heat dissipation.
f)
Minimum distance from lighted objects 1 m.
1m
g) For outdoor use.
If the glass is broekn, replace it immediately.
h)
i) If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
j) The lighting direction can not be adjusted to down ward.
EXPLANATION OF SYMBOLS:
Conforms to relevant European requirements for the product.
The crossed-out wheeled bin symbol indicates that the item should be disposed of
separately from household waste. The item should be handed in for recycling in
accordance with local environmental regulations for waste disposal. By separating a
marked item from household waste, you will help reduce the volume of waste sent to
incinerators or land-fills and minimize any potential negative impact on human health
and the environment.
TECHINICAL DATA:
Floodlight with tripod
Type
0103
Rated voltage
220-240 V ~ 50 Hz
Rated power
Max.150 W
IP54
IP Level
R7s 120 W / 78 mm
Lamp
Cable
H05RN-F 3G 1.0mm²
Weight
1.08 kg
Dimension of
133 x 92 x 4 mm
protective glass
CLEANING:
Turn off the power to clean the lamp and let the lamp cool down. Clean the lamp with soft
cloth (if necessary slightly moistened). Never use alcohol or a similar solvent, this could
damage the lamp.
All manuals and user guides at all-guides.com
INSTALLATION:
Caution: Before installation, please make sure the plug is not connected to the socket.
1. Unscrew the angle adjustment screw knob (D) from the stand. Insert the stand into the
floodlight bracket (G).
2. Align the holes of the bracket and the stand. Adjust the floodlight until the desired angle.
Then Insert and tighten angle adjustment screw knob (D).
3. CAUTION: Do note install the floodlight bracket to other tubular surface!
4. Note: Check the floodlight is secure and the stand is stable and has a firm footing. Prevent
the cable from contact with sharp objects, chemicals or hot surfaces.
5. The halogen bulb in the fitting will burn through quickly if the fitting is fixed under an angle
of more than 4°.
MAX 4°
INSTALLATION OF THE BULB:
a) Before installing bulb, please make sure the plug is not connected to the socket.
b) Loose the upper scres from the light guard and open it.
c) Take the bulb our of it's packaging. Do not touch the bulb with bare hand. Use a towel
to fix the bulb into the fitting. First press one side of the fitting against the metal pin and shift
the pin backwa
d) After chanding the light bulb, please pay attention to the correct positioning of the seal gasket.
e) Fix the light guard by tightening the screw. Do not over tighten which may damage the glass.
A.
A. Handle
A
B. Upper screws
B
MAX 4°
C. Protective grill
C
D. Angle adjustment screw knob
E. Stand
F. Mains cable
D
G
G. Floodligt bracket
F
E
rds so that you can press the other side of the bulb against the metail pin.
B.
C.
1.
2.
I
07
08
GB
V200323
Werbung
