Installation - Sygonix 43176W Bedienungsanleitung

Operating instructions
GB
LAN Colour Camera, IR
Intended use
The product is intended for surveillance by means of the integrated camera. The opera-
tion takes place via a wired 10/100MBit network (RJ45 connector). Due to its design,
the product is particularly suited for the installation on a ceiling.
The product must not get damp or wet, it is intended only for use in dry, indoor loca-
tions.
The power for the camera is supplied via the power transformer included in the de-
livery.
Please bear in mind that it is prohibited by law to watch strangers with a camera with-
out their knowledge and consent. Observe the rules and regulations of the country
where you are using the camera.
Any other use than that described above may damage the product. Moreover, this
may give rise to hazards such as short-circuiting, fi re, electric shock, etc. No part of the
product may be modifi ed or converted!
The safety instructions and technical data must be followed without fail!
This product complies with the applicable National and European requirements. All
names of companies and products are the trademarks of the respective owner. All
rights reserved.
Package Contents
• LAN Camera
• Network cable
• Installation material
• Wall plug transformer
• Mini DVD with software and an extensive operating manual in English language
(PDF)
• Quick guide
Explanation of the Symbols
The lightning symbol indicates a health hazard, e.g. electric shock.
This symbol indicates specifi c risks associated with handling, function and
use.
The "arrow" symbol indicates special tips and operating information.
Safety Instructions
The warranty will be void in the event of damage caused by failure to
observe these safety instructions! We do not assume liability for any
consequential damage!
Nor do we assume liability for damage to property or personal injury
caused by improper use or failure to observe the safety instructions. The
warranty will be void in such cases.
• The unauthorised conversion and/or modifi cation of the product is not per-
mitted because of safety and approval reasons (CE). Never dismantle the
product.
• The product is not a toy and must be kept out of the reach of children. It
should be operated out of the reach of children.
• The use of the surveillance camera system does not replace the personal
supervision of children, or people who require special assistance, but only
serves as a support to this supervision.
• The design of the wall plug transformer complies with protection class II.
Only use a proper outlet of the public supply system as a voltage source for
the power supply.
• The product should only be used in dry indoor areas, it must not become
damp or wet! There is a risk of a lethal electric shock!
• The camera should not be exposed to extreme temperatures, direct sun-
light, strong vibrations or heavy mechanical stress.
• Make sure that the connection cable is not pinched or damaged by sharp
edges.
The home technology brand for the entire house. More information at www.sygonix.com
• Do not leave packaging material carelessly lying around since it could be-
come a dangerous plaything for children.
• Handle the product with care, it can be damaged by impacts, blows, or ac-
cidental drops, even from a low height.
• If the camera is used with other devices (e.g. a monitor), the operating in-
structions and safety notices for these devices must be followed as well.
• It can be assumed that safe operation is no longer possible if:
- the device is visibly damaged,
- the device no longer works
- the device has been stored under adverse conditions.
- it was exposed to heavy loads during transport
• In commercial institutions, the accident prevention regulations of the Em-
ployer's Liability Insurance Association for Electrical Systems and Operating
Materials are to be observed.
• Disconnect the power supply from the camera if it is not to be used for a
while (e.g. for storage).
• If you have any questions that are not answered in this manual, please con-
tact our technical service or another specialist.
Connection and Control Elements
1 Brightness sensor
2 Transparent cover
3 Black shield
4 Locking screw
5 Audio input (pink)
6 Audio output (green)
7 Video output (BNC)
8 Low voltage socket
for power supply
9 RJ45 connector for
network connection
10 Terminal block
11 Camera
12 IR-LEDs

Installation

• The mounting place must be clean, dry and dust-free, also, installation and opera-
tion must not be carried out in areas where there is a risk of explosion.
• First, remove the mounting plate by rotating it slightly counter-clockwise.
• For the feed-through of the connection cable with included plugs a hole is required
that is suffi ciently big. Protect the plug connectors, e.g. with a small plastic bag,
from dust or dirt when pushing them through an aperture.
Due to the holes on the bottom, the camera can be mounted on a ceiling. Use suit-
able screws and wall plugs, depending on the surface.
Carefully rotate the camera inside in order for the screw holes to become accessible.
Don't touch the electronics.
Pay attention when drilling and tightening the screws that no cable or pipes
are damaged!
Before you close the camera's housing again, you should start up the camera so
that it can be aligned accordingly. The camera can be rotated and the inclination
adjusted. Furthermore, you can perform a focusing of the lens.
The camera should not be pointed directly at bright sources of light or the sun,
since the image will be overdriven by this.
• After start-up and adjustment of the camera, the cover must be replaced and locked
by a short, clockwise rotation. Hereby make sure that the black shield (3) is located
on the correct side.