Sygonix 43176S Bedienungsanleitung Seite 3

Operating instructions
GB
LAN Colour Camera
Intended use
The product is intended for surveillance by means of the integrated camera. The opera-
tion takes place via a wired 10/100MBit network (RJ45 connector).
The product must not get damp or wet, it is intended only for use in dry, indoor loca-
tions.
The power for the camera is supplied via the power transformer included in the de-
livery.
Please bear in mind that it is prohibited by law to watch strangers with a camera with-
out their knowledge and consent. Observe the rules and regulations of the country
where you are using the camera.
Any other use than that described above may damage the product. Moreover, this may
give rise to hazards such as short-circuiting, fi re, electric shock, etc. No part of the product
may be modifi ed or converted!
The safety instructions and technical data must be followed without fail!
This product complies with the applicable National and European requirements. All
names of companies and products are the trademarks of the respective owner. All
rights reserved.
Package Contents
• LAN Camera with objective lens
• Network cable
• Bracket with mounting material
• Wall plug transformer
• Mini DVD with software and an extensive operating manual in English language
(PDF).
• Quick guide
Explanation of the Symbols
The lightning symbol indicates a health hazard, e.g. electric shock.
This symbol indicates specifi c risks associated with handling, function and
use.
The "arrow" symbol indicates special tips and operating information.
Safety Instructions
The warranty will be void in the event of damage caused by failure to
observe these safety instructions! We do not assume liability for any
consequential damage!
Nor do we assume liability for damage to property or personal injury
caused by improper use or failure to observe the safety instructions. The
warranty will be void in such cases.
• The unauthorised conversion and/or modifi cation of the product is not per-
mitted because of safety and approval reasons (CE). Never dismantle the
product.
• The product is not a toy and must be kept out of the reach of children. It
should be operated out of the reach of children.
• The use of the surveillance camera system does not replace the personal
supervision of children, or people who require special assistance, but only
serves as a support to this supervision.
• The design of the wall plug transformer complies with protection class II.
Only use a proper outlet of the public supply system as a voltage source for
the power supply.
• The product should only be used in dry indoor areas, it must not become
damp or wet! There is a risk of a lethal electric shock!
• The camera should not be exposed to extreme temperatures, direct sun-
light, strong vibrations or heavy mechanical stress.
The home technology brand for the entire house. More information at www.sygonix.com
• Make sure that the connection cable is not pinched or damaged by sharp
edges.
• Do not leave packaging material carelessly lying around since it could be-
come a dangerous plaything for children.
• Handle the product with care, it can be damaged by impacts, blows, or ac-
cidental drops, even from a low height.
• If the camera is used with other devices (e.g. a monitor), the operating in-
structions and safety notices for these devices must be followed as well.
• It can be assumed that safe operation is no longer possible if:
- the device is visibly damaged,
- the device no longer works
- the device has been stored under adverse conditions.
- it was exposed to heavy loads during transport
• In commercial institutions, the accident prevention regulations of the Em-
ployer's Liability Insurance Association for Electrical Systems and Operating
Materials are to be observed.
• Disconnect the power supply from the camera if it is not to be used for a
while (e.g. for storage).
• If you have any questions that are not answered in this manual, please con-
tact our technical service or another specialist.
Getting Started, Connection
• If the camera's objective lens is enclosed separately, remove the protective caps
from lens and camera fi rst. Afterwards, carefully screw the objective lens into the
lens thread of the camera.
Make sure you don't touch the image senor as this will destroy it; loss of war-
ranty!
• Connect the camera's RJ45 connector to a 1:1 connected network cable and its net-
work, e.g. a network switch.
• Connect the low-voltage socket of the camera to the corresponding round plug on
the enclosed power adapter. Insert the wall plug transformer into a mains socket,
the power-LED on the front of the camera lights up.
• Insert the mini DVD provided in the appropriate drive of your computer. If the in-
stallation software does not start automatically, you must start the installation pro-
gramme manually. When this operating manual was prepared, the programme was
located in the main directory of the DVD (programme name „Autorun.exe").
Follow the program's instructions.
Be aware that the names and descriptions of the installation procedure, as described
here, may be changed in newer versions of the software. In this case please observe
the accompanying English language operating manual on the CD (PDF format).
• Start the software that you just installed („IP Discovery Tool"). It will search for
available cameras in the network. If the camera with its corresponding IP address is
shown, select the camera by double-clicking on it and then click on „Connect".
Please note:
In your network a DHCP server must be active (e.g. the DHCP server of a rout-
er). The PC must be confi gured so that it assigns an IP address automatically.
The camera is also assigned an IP address by the DHCP server.
If there is no DHCP server, the camera has the IP address 192.168.1.200 (net-
work mask 255.255.255.0). It is important that this IP address is not already
used by another device in the network. Otherwise, there is no access to the
camera!
• If the camera requests a user name and password, you have to enter „admin" for
both (written in lower case letters and without quotation marks).
• We recommend you to use Internet Explorer as the internet browser in order to be
able to use all functions of the camera. Prior to connecting to the camera, you have
to install an ActiveX plug-in.
Depending on the security settings for your Internet Explorer an error message ap-
pears, saying a required ActiveX element cannot be installed or that the installation
of the ActiveX can be started manually by clicking on the information bar.