Compliance Information - DJI Ronin 4D Benutzerhandbuch

Compliance Information

FCC Compliance Notice
Supplier's Declaration of Conformity
Product name: DJI Ronin 4D Video Transmitter
Model Number: TX2
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com
We, DJI Technology, Inc., being the responsible party, declares that the above
mentioned model was tested to demonstrate complying with all applicable FCC
rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and any part of your body.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio
waves established by the Federal Communications Commission (USA). These
requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The
highest SAR value reported under this standard during product certification for
use when properly worn on the body.
ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada's licence-exempt
RSS(s). Operation is subject to the following two conditions: (1)This device may
not cause interference.(2)This device must accept any interference, including
interference that may cause undesired operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est
24
conforme aux CNR d'Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes :(1)L'appareil ne doit pas produire de
brouillage; (2)L'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies with ISED radiation exposure limits set forth for
an uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio
waves established by the ISED.
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED
établies pour un environnement non contrôlé. L'utilisateur final doit suivre les
instructions spécifiques pour satisfaire les normes. Cet émetteur ne doit pas
être co-implanté ou fonctionner en conjonction avec toute autre antenne ou
transmetteur. Le dispositif portatif est conçu pour répondre aux exigences
d'exposition aux ondes radio établie par le développement énergétique
DURABLE.
These requirements set a SAR limit of 1.6 W/kg averaged over one gram of
tissue. The highest SAR value reported under this standard during product
certification for use when properly worn on the body.
Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de
tissu. La valeur SAR la plus élevée signalée en vertu de cette norme lors de la
certification de produit à utiliser lorsqu'il est correctement porté sur le corps.
No operation is permitted for the frequency "5600-5650MHz"
Aucune opération n'est autorisée pour la fréquence « 5600-5650MHz »
For devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the bands 5250-5350 MHz and 5470-5725 MHz, 5725-5850
MHz shall be such that the equipment still complies with the e.i.r.p. limit as
appropriate.
Le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 5250-
5350 MHz et5 470-5 725 MHz, 5725-5825 MHz) doit se conformer à la limite
de p.i.r.e. spécifiée pour l'exploitation point à point et non point à point, selon le
cas.
KCC Compliance Notice
"해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서
비스는 할 수 없습니다 ."
"해당 무선설비는 운용 중 전파혼신 가능성이 있음"
NCC Compliance Notice
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用不得
影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至
無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通
信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設
備之干擾。
注意：
應避免影響附近雷達系統之操作。
高增益指向性天線只得應用於固定式點對點系統。