Werbung
Verfügbare Sprachen
Verfügbare Sprachen
USAGE NOTES and FUNCTIONS
3. SETTING the SEAT
3.1 SEAT HEIGHT
3.1.1 Raise the right front lever R1
3.1.2 RETRACTING the seat: LOADING the seating surface
3.1.3 EXTENDING the seat: UNLOADING the seating surface
NOTE: As soon as the lever 3.1.1 is no longer actuated,
NOTE:
the seat remains in the set position.
3.2 SEAT INCLINATION
3.2.1 Lift the lever on the left L firmly and hold it in place,
3.2.1
by SHIFTING THE BODY WEIGHT set the incline of
3.2.1
the seat as desired:
3.2.2 - backwards (~2°) or
3.2.3 - forwards (~10°).
NOTE : As soon as the lever 3.2.1 is no longer actuated,
NOTE :
the seat remains in the selected incline.
4. ADJUST the BACKREST
4.1 BACKREST HEIGHT
4.1.1 Hold the backrest and loosen the clamping screw.
4.1.2 Then push the retaining tube to the desired height
4.1.2
and secure the position of the backrest by tightening
4.1.2
the clamping screw.
4.1.3 The maximum height of the backrest is limited by a
4.1.3
stop bolt. See chapter 2. ASSEMBLY, Position 2.6
4.2 BACKREST CUSHION
4.2.1 The backrest-cushion is firmly connected to the retaining
4.2.1
tube, but can nevertheless be rotated by approx. 30°.
4.2.2 There is no need for any pre-adjustment, since the
4.2.2
upholstery automatically adapts to the user's back.
4.3 BACKREST INCLINATION
4.3.1 Push down the right rear lever R2...
4.3.2 ...and the backrest swings forwards.
4.3.3 Select the desired position through back pressure...
4.3.4 ...and secure it by lifting lever R2.
5. ADJUST the FOOTREST
5.1 FOOTREST HEIGHT
5.1.1 Hold the footrest and loosen the clamping screw
5.1.2 Push the footrest to the desired height
5.1.2
NOTE: maximum height 420 mm, see 5.3.1
5.1.3 Secure position by tightening the clamping screw.
5.2 FOOTREST ALIGNMENT
5.1.1 Hold the footrest and loosen the clamping screw
5.2.2 Turn the footrest in the desired direction (360°)
5.1.3 Secure position by tightening the clamping screw.
5.3 WARNING! Danger of crushing due to footrest
5.3.1 Measure 1 to protect the fingers.
5.3.1
- Establish a safety distance: for this purpose, set the
5.3.1 -
footrest to max. 420 mm height (= 30 mm below the
5.3.1 -
base tube)
5.3.2 Measure 2 to protect your feet.
5.3.2 - Avoid unintentional retraction/sinking: take care not to
5.3.2 -
move the control lever of the height adjustment (=R1)
5.3.2 -
with your heel.
CHECK, MAINTENANCE, CLEANING
- Watch out for hazards during maintenance work (jamming...)
- For cleaning, use a slightly damp cloth and a non-abrasive
-
cleaning agent
FAULT-FINDING (F) and REPAIR (R)
F: Bass stool wobbles
F:
R: Check the surface for suitability
F:
R: Foot stand and base plate complete and in good order?
F: Seat, backrest, footrest too high/low/etc.
F:
R: Change settings
F: Bass stool cannot be adjusted as desired
F:
R: See operating instructions:
F: R:
Follow procedure/limitations of settings
TECHNICAL DATA
Tubes: Steel, powder coating, black
Seat mechanic, pneumatic spring Steel, diverse
Material
Connection elements: Steel, galvanized
Caps, grips, guides: PA, PE
Cushion covering: Trevira CS (flame retardant)
Load-bearing
1 Person, 100 kg (static load)
Root circle diameter 630 mm
Dimensions
Seat surface: 430 x 390 mm
Seat height: 595-850 mm
Cardboard
B x T x H: 600 x 600 x 640 mm
Weight
net : 12.2 kg; gross: 14.4 kg
3.1 SEAT: Height
Top view
3.2 SEAT: Inclination
Top view
4.1 BACKREST: Height
4.3 BACKREST: Inclination
Top view
4.2 BACKREST: Cushion
5. FOOTREST: 5.1 Height and
5. FOOTREST:
5.2 Alignment
5.3 WARNING! Danger of crushing
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
13460-019-55 Rev.03 03-80-436-00 11/21
Werbung
