Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1. Commissioning / operation
Please remember that the voltage in the building being
cleaned must concur with that given on the machine's type
plate.
1.1 Assembly instructions
The motor head and bar are supplied separately
☞
packed.
First release the hexagon socket srews in the shaft
☞
adjustment unit (9).
Then feed the bar (6) gently as far as it will go into the
☞
shaft adjustment unit (9).
Align the handle bar (1) parallel with the wheels (10),
☞
so that the open side of the housing of the top shaft
element (3) is facing to the rear.
Then tighten the hexagon socket screws (9) again.
☞
Wind the electric cable (12) around the handle bar (1)
☞
and cable hook (8).
1.2 Preparations for use
☞ Grasp the handle bar (1) with
1
both hands and tip the machine
until it is resting on both wheels (A).
☞ Then run the machine to place
of work and attach the pad (19).
A
☞ To this end, slide the pad (19)
11
with ist central recess over the
yellow connector and fasten it with
18
the yellow fastening (14) nur.
14
☞ Make sure that the pad is
properly centred and tighten the
nur firmly.
☞ It mist not protrude beyond the
pad surface.
☞ Before starting the machine,
set the front wheel (11) to ist
maximum height (-), which is equal
to the lowest pressing force.
☞ Make sure that the swivelling
11
action is unimpaired.
If
the
cleaning
effect
☞
unsatisfactory, increase the pressing force slightly (+).
Only set the lowest possible pressure.
☞
Always uncoil all of the mains cable (20 m).
☞
1.3 Machine use
3
2
☞ Press the drive plate motor
4
switch (2) (right or left) to start the
2
6
motor.
☞ If you raise the shaft (6) slightly,
the machine moves to the right.
☞ If you lower the shaft, the
machine
☞ If you keep the shaft in ist
central
operates
6
☞ On
machine (A) before starting the
motor and only then lower it onto
the floor.
R 53-1100/1500 UHS
.
and
gloss
finish
are
moves
to
the
left.
position,
the
machine
on
the
spot.
rough
floors,
tip
the
1.3 Machine use
☞ The machine is equipped with
an overload indicator (17) (for
17
excessive pressing force).
☞ This lamp should not or only
briefly light up.
1.4 After use
Pull the shaft adjustement lever (4) and setz the shaft
☞
(6) in ist vertical position.
Now pull the mains plug out of ist socket and coil the
☞
electric cable (15) around the handlebar (1) and cable
hook (8).
To protect the retaining needles, leave the used pd
☞
screwed onto the drive plate until the machine is used
again. Only then replace it with a new pad.
The vacuum ring (22) must from time to time be
☞
washed clean.
For this maintenance, you take it off.
☞
If the machine can be tipped suction ringpull easy.
☞
Assemble in reverse order.
☞
2. Assembly instructions for Spraymaster
Fit the holder for the spray can to the bar (6) with the
☞
holder pointing upwards and, when viewed from the
operating side, to the left.
Hook the spray can's tongue onto the holder, pivoting
☞
the holder back until the ball catch engages.
Then slide the spring clip over the shaft adjustment
☞
unit (9).
Attach the box on the right or left as desired.
☞
Point the universal-jointed hose in the desired
☞
direction.
3. Cleaners
Equip your machine with the following accessories for
☞
cleaner spraying:
Spraymaster (20) and the brown pad (19).
Fill the spray with the desired product.
☞
Attach the pad to the drive plate.
☞
Then start the machine.
☞
☞ Pull the hand lever on the Spray-
B
master (20) a few times to spray the
cleaner product onto the floor. Start cleaner
spraying immediately, continuing until a
gloss is produced (B+C).
☞ We recommend cleaning the floor
section by section.
With the R 53-1100 and R 53-1500 you can
clean at a far greater speed than with
C
slower machines.
The machine is ideal for cleaning with
polymer dispersions. The coating's traffic
resistance and hardwearing properties
remain unaffected. Smears can be
removed easily.
Polishing / cleaning
4.
For these tasks, we advise using the red pads.
☞
This is fastest way of removing smears and scratches
☞
and producing the typical wet gloss.
Englisch 8
Werbung
Inhaltsverzeichnis
