Safety Instructions; Product Description And Specifications; Product Features; Technical Data - Bosch BDS3210 Originalbetriebsanleitung

Safety instructions

Read all the safety information and in-
structions. Failure to observe the safety in-
formation and follow instructions may result
in electric shock, fire and/or serious injury.
Save all safety warnings and instructions for future ref-
erence.
The contact surfaces of the display holder may be-
u
come very hot (> 60 °C). Allow the contact surfaces to
adjust to the ambient temperature before you touch
them. This is particularly important when using a Smart-
phoneGrip.
Keep swallowable small parts away from small chil-
u
dren. There is a risk of serious injury.
Never short-circuit the pins. The display holder may be
u
irreparably damaged and must then be replaced.
Ensure that the contacts are free of dirt. By doing this,
u
you prevent malfunctions or damage.
After a fall, check the display holder for sharp edges.
u
Replace it if required.
Do not stand your bicycle upside down on its saddle
u
and handlebars if the on-board computer or its holder
protrude from the handlebars. This may irreparably
damage the on-board computer or the holder. Also re-
move the on-board computer before placing the bicycle
on a wall mount to ensure that the on-board computer
does not fall off or become damaged.
Observe all national regulations which set out the ap-
u
proved use of eBikes.
Read and observe the safety warnings and directions
u
contained in all the eBike system operating instruc-
tions and in the operating instructions of your eBike.
Product description and
specifications
Intended use
The display holder is intended to establish the mechanical
and electrical connection to a display or on-board computer.
Only original Bosch eBike components can be connected to
the display holder.
A display holder is not required for an eBike system to func-
tion.

Product features

The numbering of the components shown refers to the illus-
trations on the graphics pages at the beginning of the
manual.
(1) Display mount
(2) Adapter tray
(3) Clamp for holder
(4) Clamp screw
Bosch eBike Systems
(5) Round rubber spacer
(6) 1-arm socket
(7) Screw for adjusting tilt
(8) Removal blocker
(9) Snap-in hook
(10) Connection cables
(11) Fastening screws for display mount
The display mount (1) can also be embedded in the bicycle
design.

Technical data

Display holder
Product code
Output voltage
Output current, max.
Operating temperature
Storage temperature
Protection rating
Fitting
Installation positions (see figure A)
The 1-arm socket can be mounted at three different posi-
tions on the handlebars:
– In front of the handlebars ➀
– Over the stem ➁
– In the triangle between the stem and handlebar ➂
Note: In order to ensure clean cable routing, the appropriate
display mount must be used for each of the three different
positions: The BDS3210 display mount for in front of the
handlebars (electrical connections at the rear); the
BDS3250 display mount for over the stem or in the triangle
between the stem and handlebar (electrical connections at
the front).
If you want to change the installation position and you have
the correct display mount (1), you must first remove the 1-
arm socket (6) and re-mount it afterwards.
Note: Please be aware that there are two different handlebar
diameters (31.8 mm and 35 mm). Your bicycle retailer will
help you to select the correct components.
Mounting the display mount (see figure B)
Insert the display mount (1) into the adapter tray (2). En-
sure that it is in the required installation position. Secure the
display mount (1) from below using the screws (11). When
English – 1
BDS3210
BDS3250
BDS3620
BDS3630
V 4.75 to 5.4
A 1.5
°C –5 to +40
°C +10 to +40
IP54
0 275 007 3S1 | (09.06.2021)