Werbung
Verfügbare Sprachen
Verfügbare Sprachen
USAGE NOTES / FUNCTION
6. COMPONENTS
6.A - 18805 Sheet music and concept holder
6.B - 26749 Monitor plate M
6.C - 211 ff Boom arms
6.D - 19744 ff Tablet PC stand holder
6.E - Various products with threaded connector
NOTE!
Threads must a be screwed on at least three
full turns and b be clamped backlash-free with
the knurled washer f 8.3
SETTINGS
This 18817 Universal holder
i.e. its components (18805, 211... etc.)
can be adjusted in height, direction, angle
and distance.
In addition, the keyboard stands
can be adjusted to different positions.
WE RECOMMEND:
Prior to adjusting the holder and transport:
the stand should only be transported
after any equipment has been removed.
7. HEIGHT (STAND TUBE position)
7.1 Unscrew clamp screw d
7.1
completely and...
7.2 ... place the stand tube a in one
7.2
of the possible 8 positions;
7.2
Screw the clamp screw back in
8. DIRECTION ( ATTACHMENT)
8.1 Loosen the knurled washer f and...
8.2 ...place the attachment in the
8.2
desired direction;
8.3 Re-tighten the knurled washer
NOTE: The attachment must be screwed on
by at least three full turns.
9. INCLINATION (ATTACHMENT)
9.1 Loosen the locking nut on the side and...
9.2 ...tilt attachment (plate, boom, PC holder)
9.2
as desired.
9.2
Re-tighten the wing-nut 9.1.
10. DISTANCE (STAND TUBE – KEYBOARD REST)
10.1 Loosen the knurled screw c and...
10.2 ...push insertion tube b to the end and secure
10.2
position again by tightening knurled screw.
NOTE 1: The knurled screw must always protrude
into the slot of the insertion tube. This limitation of
movement increases the safety of the installation.
NOTE 2: Extending the distance can result in an
unfavorable weight distribution. Ensure that the
stability of the stand is guaranteed, in any case.
MAINTENANCE and CLEANING
- During maintenance work, watch out for possible
-
hazards (jamming, bumping)
- For cleaning, use a slightly damp cloth and non-
-
abrasive cleaning agents
FAULT-FINDING (F) and REPAIR (R)
F: Installation is not stable
F: R: Check to see if the parts are in the right positions
F: R:
and the screws are properly tightened.
F:
B: Make sure that the insertion tube has been
F: B:
mounted correctly, with the slot facing
F: B:
downwards. The knurled screw must be
F: B:
inserted into this slot..
F:
R: Check to see that the keyboard stand
F: R:
is properly setup.
TECHNICAL DATA
Tubes , horizontal support:
Steel, powder-coated, black
Material
Screws, disks: Steel, galvanized
Knurled washer : Alu, black
Plastic parts: PA, PE, black
Load
Max. load-bearing capacity 8 kg
Stand tube: ø 25 x 450 mm - 3/8"-5/8"
Height adjustment 294 mm (7 x 42 mm)
Dimensions
Horizontal support: 25 x 15 x 225 mm
Depth adjustment : 90 - 136 mm
Box
535 x 150 x 80 mm
Weight
0,85 kg
Accessories see chapter 6.A - E: Components
6. COMPONENTS
6.A - 18805 Sheet music holder
6.C - 211 ff Boom arms
6.D - 19744/90/95 Tablet holder
6.E - various
85035 ff
8. DIRECTION
Bsp. 18805 Sheet music and concept holder
10. DISTANCE:
between 18817 universal holder and 18800/10/20 »Omega« (Assembly per 18814 Adapter)
10. ABSTAND:
between 18817 universal holder and 18950/53 Table-style keyboard stand (direct assembly - without adapter)
10. ABSTAND:
between 18817 universal holder and 18950/53 Table-style keyboard stand (Assembly per 18954 Adapter)
7. HEIGHT
6.B - 26749 Monitor plate M
223 ff
7-232-
000155
9. INCLINATION
Bsp. 197.. Tablet PC stand holder
Example
18805 Sheet
music and
concept holder
Example
18950
18953
Table-style
keyboard
stand
Werbung
