Werbung
Verfügbare Sprachen
Verfügbare Sprachen
18817 Universal holder
INTENDED USE
The universal holder extends:
a. Table-style keyboard stands (18950, 18953) as well as
b. Keyboard tables of the »Omega«-series (18800/10/20)
with: - Sheet music holder (18805) - Monitor plate M (26749)
with:
- Microphone-boom arms (211, 21110, 21140 ff)
with:
- Tablet PC stand holder (19744 /90 /95)
with:
- Goosenecks (223 ff) - Microphone clips (85035 ff)
FEATURES & CAPABILITIES
- adjustable in height (up to 294 mm) and depth
- with 3/8" connection thread plus 5/8" thread adapter
- for direct assembly (18950, 18953)
- Mounting using adapter: 18814 (18800/10/20), 18954 (18950/53)
Thank you for choosing this product. Please read and follow carefully the instructions.
They inform you about all important steps, that are required for a safe assembly and
operation. Please keep the instructions for future reference.
SAFETY NOTES
- Max. load capacity 8 kg
- Protect from moisture/wetness
- Carry out a visual inspection before and after use and check for completeness and possible damage.
-
A damaged product must not be used again until it has been repaired.
- The slot of the horizontal support tube b must be mounted pointing downwards so that the knurled screw c
-
can protrude into it. This may only be disengaged for disassembly.
- Ensure tight screw connections of all items involved.
- Observe the safety instructions and assembly instructions of the keyboard stands and adapters involved.
SETUP INSTRUCTIONS
1. COMPONENTS
a Stand tube with threaded bolt 3/8"
b Horizontal support (half shell of the insertion tube)
b
Accessory bag:
c Knurled screw M6 x 20 mm
d Clamp screw M8 x 33 mm
e Thread adapter 3/8"-5/8"
f Knurled washer ø 28 x 3/8"
2./3./4. Installation of the horizontal support
There are three options:
2. 18800, 18810, 18820 »Omega«-series
2.
- with 18814 ADAPTER
2.1 Install 18814 Adapter (see Instruction 18814)
2.2 Place the insertion tube b into the adapter
2.2
as far as it will go
2.3 Secure the position by tightening
2.3
the knurled screw c
2.4 Depth adjustment: 0-90 mm
3. 18950/18953 TABLE-STYLE KEYBOARD
3.
STAND - DIRECT
3.1 Remove the cap from the tube on
3.1
the table-style keyboard stand
3.2 Place the insertion tube b into the stand
3.2
tube as far as it will go
3.3 Secure the position by tightening
3.3
the knurled screw c
3.4 Depth adjustment: 0-131 mm
4. 18950/18953 TABLE-STYLE KEYBOARD
4.
STAND - with 18954 ADAPTER
4.1 Install 18954 Adapter (see Instruction 18954)
4.2 Place the insertion tube b into the adapter
4.2
as far as it will go
4.3 Secure the position by tightening
4.3
the knurled screw c
4.4 Depth adjustment: 0-136 mm
5. ASSEMBLY of the stand tube; for example:
3. 18950/18953 TABLE-STYLE KEYBOARD
3.
STAND - DIRECT
5.1 Have the clamp screw d ready
5.2 Hold the standing tube a at the desired
5.2
height (8 steps) to the half shell of the
5.2
insertion tube b and...
5.3 ... secure this position by tightening
5.3
the clamp screw d
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
18817-000-55 Rev.11 03-79-262-00 10/21
18814 Adapter
18800/10/20
»Omega«
Stativrohr
18950/53
Table-style keyboard stand
18954 Adapter
18950/53
Table-style keyboard stand
Stop
Stop
Stop
18950/53
Table-style keyboard stand
Werbung
