Werbung
Verfügbare Sprachen
Verfügbare Sprachen
USAGE NOTES / FUNCTION
5. POSITION OF THE OPERATING ELEMENTS
Both stacker parts function in the same manner.
They do differ in the position of the operating elements (1.6 small nut):
The support tube right 1.8 has the clamp nut on the right side.
The support tube left 1.9 has the clamp nut on the left side.
There are two installation options, i.e. one can select between:
5.1 operating elements located on the inside
5.2 clamp nuts located on the outside
6. POSITION OF THE STACKER
6.1 SYNCHRONOUS ADJUSTMENT
6.1
The front part of the stacker tube should
6.1
be the same, i.e. parallel to the cross tube
6.1
of the keyboard stand.
6.2 DEPTH - VARIABLE ADJUSTMENT
6.2
(0-35 mm)
6.2
The L-base tube 1.7 has a 35mm long slit,
6.2
which provide for the variable adjustment
6.2
of the stacker.
6.a Loosen the clamping nut a bit...
6.b ...and place the L-base tube in the
6.b
desired position,
6.c Tighten the clamping nut
6.3 DEPTH - PRESET
6.3
(0-25-50-75-100 mm)
6.3
The support tubes 1.8/1.9 can be placed in
6.3
five different positions, in 25 mm intervals
6.3
connecting to the L-base tube.
6.d Unscrew the screw connection 1.4-6.
6.e Lift the support tube 1.8 from the base tube 1.7...
6.f ...and place it in the desired position.
6.g Ensure that both ends of the L-tube are
6.g
placed in the corresponding opening of
6.g
the stacker.
6.h Place the hexagon screw (M5 x 45 mm)
6.h
from the side, place the U-disk and clamp
6.h
nut and tighten.
6.i Ensure that the hexagon of the screw is
6.i
placed in the opening (hole) such
6.i
that it cannot be turned.
FAULT-FINDING (F) and
REPAIR (R)
F: The stacker cannot be secured
F:
B: Wrong base, i.e. Stacker 18813 must
F: B:
be replaced with Stacker 18811
F: The stacker is not stable
F:
B: Tighten the clamping nuts 1.1/1.6
F:
B: Ensure that the hexagon is properly
F: B:
placed in the opening (hole) 4.f/6.i
F:
B. Check that the screw connection of
F: B:
the base table and Stacker 18811
F: B:
is tight
F: The keyboard is not balanced
F:
B: Ensure that the extensions 1.8/1.9
F: B:
have the same depth adjustment (see Section 6)
F:
B: Ensure that the base table and
F: B:
stacker are adjusted properly
CHECK, MAINTENANCE, CLEANING
- In the event of maintenance pay attention to possible risks
- To care for the product, use a damp cloth and a non-abrasive
-
cleaning agent.
TECHNICAL DATA
Tubes: Steel, powder coating, black
Material
Screws, disks: Steel galvanized
Plastic parts: PA, PE, TPE, black
Load
max. 15 kg
Stacker: Width: 40 mm, Depth: 280 mm, Height: 227 mm
Dimensions
Distance: centered 122 - 732 mm (see 18810)
Weight
1.7 kg
Packaging
L x W x D: 485 x 260 x 50 mm
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
18821-000-55 Rev.04 03-79-261-00 12/17
All manuals and user guides at all-guides.com
5. OPERATING ELEMENTS
6. STACKER
7. DIMENSIONS
Werbung
