Werbung
Verfügbare Sprachen
Verfügbare Sprachen
18821 Stacker
- for Table-style keyboard stand 18810 »Omega« with Stacker 18811
- Ideal for a third device
- Load bearing weight max. 15 kg
- Variable depth adjustment (135 mm)
- Height: 225 mm, Width: 40 mm, Stacker depth: 280 mm
- Only suitable for Stacker 18811, Not for 18813
Thank you for choosing this product. The instructions provide directions to all of the important setup and handling steps. We recommend you keep these
instructions for future reference.
SAFETY NOTES
- Please observe the associated safety notes
-
for 18810 and 18811
- Ensure that the connection of the stacker is secure
- Both stackers 1.8/9 are to be placed at the same depth
SETUP INSTRUCTIONS
1. COMPONENTS
Stacker 18821 comes completely pre-assembled
and consists of the following individual parts:
1.1 Clamping nut M6 (2x) - in the accessory bag
1.2 U-Disk ø 6,4 mm (2x) - in the accessory bag
1.3 Hexagon screw M6 x 28 mm (2x) - in the accessory bag
1.4 Hexagon screw M5 x 45 mm (2x)
1.5 U-Disk ø 5,3 mm (2x)
1.6 Clamping nut M5 (2x)
1.7 L-Base tube (2x)
1.8 Support tube right
1.9 Support tube left
1.10 Rubber caps (2x)
2. PREPARATION
First the two products:
- 18810 »Omega« Keyboard-Base Table,
- 18811 Stacker, adjustable, for »Omega«,
are setup, according to the respective
setup instructions.
3. DETERMINE THE STACKER DISTANCES
Then clarify the distance the 18811 Stacker
is to have 3.1/3.2. Attach this onto the »Omega« 18810.
3.1 SMALL DISTANCE
3.1
e.g. for laptop:
3.1
- The stacker tubes of 18810 »Omega«
3.1 -
the wide stacker stays on the stand
3.2 LARGE DISTANCE
3.2
e.g. for an additional keyboard:
3.2
- The stacker tubes of 18810 »Omega« can be
3.2 -
removed due to the "competition" between the
3.2 -
stacker tubes
NOTE:
The distance of the upper stacker equals the lower stacker.
Should the devices require different distance, we
recommend the use of 18819 on the bottom and 18824 on
the top.
4. MOUNT 18821 STACKER
The only difference between the stackers is the position of the
clamping nuts. They can be applied on the inside or the outside
(see Section 5).
4.a Remove the back tube cap for 18811
4.b Remove the screws from holding tube strut 18821
4.c Place the strut in the open tube
4.d Place the hexagon screw from the top
4.d
until it is level in the hole
4.e Place the U-disk and nut from below and tighten
4.f Check to ensure that the nut is tight:
4.f
- The screw head is level and tight in the drill hole
4.f
- The wing nut has been tightened as far as it will go
4.f
- The tube is secure and can no longer be moved
4.f -
by hand
4.g Mount the second stacker tube in the same manner.
4.g
Both stacker tubes must be adjusted to the same depth.
All manuals and user guides at all-guides.com
1. COMPONENTS
3. DETERMINE THE STACKER DISTANCES
4. MOUNT 18821 STACKER
2. PREPARATION
Werbung
