Conrad 41 75 72 Bedienungsanleitung Seite 2

3.5" IDE Hard Disk Drive Enclosure
Item no. 41 75 72 black
Item no. 41 75 73 silver
1. Intended use
A 3.5" IDE hard disk can be installed in the enclosure. It can be operated via a USB 2.0 interface. The enclosure
features an additional power supply.
Only use in dry indoor locations.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and product
names are trademarks of their respective owners. All rights reserved.
2. Delivery content
• Hard drive enclosure • 2x fillister head screws
• USB 2.0 cable • 2x countersunk screws, short
• Power adapter • 2x countersunk screws, long
• Foot • Operating instructions
3. Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
Persons / Product
• As power supply, only use the supplied mains adaptor.
• Only connect the power adaptor to a normal mains socket connected to the public supply. Before plugging
in the power adaptor, check whether the voltage stated on the power adaptor complies with the voltage of
your electricity supplier.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power adaptor from the mains socket by pulling on the cable; always use the grips on
the plug.
• When setting up the product, make sure that the cable is not pinched, kinked or damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them. This poses a risk of injury.
• For safety reasons, disconnect the power adaptor from the mains socket during storms.
• Grasp the hard disk laterally in the housing, do not touch the plate with the electronics. Electrostatic
discharge can destroy the hard disk.
• When setting up the product, make sure that the cables are neither kinked nor pinched.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous playing material
for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
• Also observe the safety and operating instructions of any other devices which are connected to the product.
Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
4. Installation of a 8.89 cm (3.5") IDE hard drive
1. Unscrew the two fillister head screws (if installed) from the enclosure cover.
2. Carefully pull the enclosure cover including the board and hard disk bracket from the enclosure.
3. Align the IDE port of your hard disk to the board's IDE plug and then connect the hard disk to it.
4. Connect the power plug to the hard disk, observing the correct polarity.
5. Fasten the hard disk from below to the mounts, using the two short countersunk screws.
6. Slide the bracket back into the enclosure until the enclosure cover is closed again. Carefully observe the run
of the lateral guide rails inside the hard disk enclosure.
7. Screw the two long countersunk screws back on from the outside of the enclosure, in order to stabilise the
hard disk inside.
8. Fasten the enclosure cover with the two fillister head screws.
5. Positioning
• Plug the stand onto the enclosure and place it on a level surface.
• Alternatively, you can put the enclosure down flat. Place it on a level surface.
All manuals and user guides at all-guides.com
6. Operation
1. Ensure the power switch on the back of the hard disk enclosure is in the OFF position.
2. Connect the mains cable to the hard disk enclosure. Insert the mains plug into the wall outlet.
Version 12/12
3. Connect the USB 2.0 cable to the hard disk enclosure and the USB plug to a free USB port on your PC.
4. Put the power switch to ON in order to turn the product on.
5. When the LED lights up, the device will be ready for use.
6. When data exchange takes place, the LED flashes.
7. After use, turn the device off using the power switch. When the product will not be used for longer periods of
7. Tips and notes
• USB 2.0 devices are backwards compatible. This means that the hard disk drive can also function with
• You should, however, take into account that data may be corrupted or the operating system may crash if
• Always treat hard disks with care. Impacts during operation (also for a few seconds after switching off) may
• When connecting the hard drive for the first time, it may take up to one minute for it to be recognised. The
• A new hard disk has to be partitioned and formatted before it can be used and displayed e.g in the
• With Windows® 7, navigate in the Control Panel to "System and Security". Click on "Administrative Tools"
• There, select the correct hard drive and create a new partition. Afterwards, the hard drive needs to be
8. Cleaning
• Before cleaning, disconnect the product from the computer and the mains.
• Use a clean, dry soft cloth for cleaning. Do not use any aggressive cleaning agents as these may result in
9. Disposal
10. Technical data
Hard drive enclosure
Suitable for:
Data transmission rate:
Connection:
System requirements:
Cable length (USB):
Dimensions (W x H x D):
Weight:
Power supply unit
Input voltage / current:
Output voltage / current:
© 2012 by Conrad Electronic SE.
time, unplug the mains plug from the wall outlet and disconnect the USB plug from your computer.
conventional USB 1.1 ports, but then only at the maximum USB 1.1 speed.
the connection cable is disconnected while data are being transferred (or the cabinet is switched off or the
power unit is disconnected).
cause the write/read head to touch the magnetic disk, which destroys the hard disk.
time may vary depending on operating system and hardware used.
Windows® file manager.
and then on "Create and format hard disk partitions".
formatted.
discoloration of the housing.
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
3.5" (8.89 cm) IDE hard drive
USB 2.0
USB 1.1
USB 2.0 / USB 1.1
Windows® XP (32bit)/ Vista™ (32bit, 64bit)/ 7 (32bit, 64bit), 8, Mac OS
10.7 or above, Linux Ubuntu 11.4 or above
90 cm
193 x 31 x 113 mm
374 g
100 – 240 V/AC; 50/60 Hz; 0.6 A
12 V/DC / 2 A
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
up to 480 MB/s
up to 12 MB/s
V2_1212_02-JH