Warranty; Limitation Of Liability; Intended Use; Important When Unpacking - Landig W 100 Bedienungsanleitung

• Always place the meat mincer on a firm and stable surface.
Make sure that the device is not near the edge of the work-
top where it can easily be pushed away or fall.
• The gearbox case and motor cover can get hot during oper-
ation, which is normal. Do not touch these parts
during operation.
• Do not attempt to operate the device when the motor and
gearbox are cold. The temperature of the mincer attach-
ment, the motor and the gearbox should be at least +7˚C
before starting.
• To reduce the risk of accidental start-up, make sure that
the controller is switched off before inserting the plug
into the socket.
• When storing the device, always pull the plug out of the
socket, otherwise there is a risk of fire, especially if the
device touches the walls or the door of the cabinet.
• Never connect the meat mincer where water can get into
the set-up area.
• To protect yourself from the risk of fatal electrocution, never
immerse the meat mincer in water or other liquids.
• Make sure that the mincer attachment is disconnected from
the motor block before cleaning.
• Never rinse the motor block under running water; only use
a damp cloth to clean it. The motor block has an anti-fin-
gerprint finish, please do not damage it by scratching it or
cleaning it too intensively with brushes or sponges.
• Never operate the meat mincer with wet hands or when you
are standing on a wet floor.
• The use of attachments or parts not expressly sold for the
device or sold by Landig will void the warranty and could
result in fire, electrocution or injury.
WARNING
Only wash stainless-steel parts in your dishwasher!
Do not use any aggressive cleaning agents!
• Never place the device near a hot burner, in an oven or in
a dishwasher.
• Never use abrasive cleaning agents or abrasive cloths to
clean the mincer attachment or the motor block.
• Never use the meat mincer for any purpose other than that
for which it was intended. Details see page 19 (intended
Use).
18
WARNING
Never work dry!
Damage caused by dry operation will void the
guarantee.
• Never let the meat mincer run dry for more than 10 seconds
without meat in the device. The friction between the auger
and the meat mincer head creates high heat, which can
cause the meat to stick to the inside of the meat mincer.
• Never try to grind bones, nuts or other hard objects.
• Wear eye protection, e.g. protective goggles, when working.
Everyday glasses are not protective goggles. Protective gog-
gles meet the requirements of ANSI Z87.1. Note: Approved
protective goggles are printed or stamped with Z87.
• The manufacturer declines all responsibility in the event of
improper use of the device. Improper use will automatically
void the guarantee.
• Never use the device while under the influence of drugs
or alcohol.

Warranty

The motor of your meat mincer comes with a lifelong guaran-
tee (25 years from the date of purchase) provided it is used and
cared for properly.
All other parts of the meat mincer are covered by a 2-year
manufacturer's warranty for defects that can be traced back to
manufacturing and material defects. Your statutory warranty
claims according to § 439 ff. German Civil Code-E remain
unaffected by this regulation.
The warranty does not include damage caused by improper
handling or use, or defects that only marginally affect the
function or value of the device. In addition, Landig assumes no
liability for damage caused by lack of or inadequate mainte-
nance. In this case the guarantee is also void. In addition, dam-
age in transit is excluded from the warranty claim insofar as
Landig is not responsible for this. A warranty claim is excluded
for damage caused by repairs not carried out by Landig or an
official agency.
In the event of justified complaints, Landig will either repair
the defective product at its own discretion or replace it with a
defect-free product. Further details can be found at:
https://www.landig.com/garantie

Limitation of liability

All technical information, data and instructions for installation,
operation and cleaning / care contained in these instructions
for use correspond to the latest status at the time of printing
and are based on our previous experience and knowledge to
the best of our knowledge.
Please note that no claims can be derived from the informa-
tion, images and descriptions in these instructions.
The manufacturer assumes no liability for damage due to:
• failure to follow the instructions
• improper use
• technical modifications
• improper repairs
• use of unapproved spare parts
The manufacturer assumes no liability for translation errors.
Only the original German text remains binding, in which punc-
tuation and character errors cannot be ruled out either.

Intended use

You have chosen a high-quality Landig meat mincer. This de-
vice is not intended for intensive daily use in commercial and
industrial areas. Please note the information on the maximum
throughput:
W 100: 100 kg/h, WD 100: 130 kg/h, W 200: 150 kg/h,
WD 200: 195 kg/h, W 300: 200 kg/h and WD 300: 260 kg/h.
Only use the device indoors (closed rooms). You can use this
device to process meat, sausage products, poultry, fish, ham/
bacon and dough. Never crush hard objects such as bones or
frozen food.
The device is intended for use in the household and hobby area
(hunting, fishing, agricultural self-marketing), as well as for use
in small meat processing businesses and similar areas.
Any other use that goes beyond this is considered improper
use.
This device can pose considerable dangers if it is not used
as intended!
• Use the device only as intended!
• It is imperative that you adhere to the procedures described
in these instructions for use.
Claims of any kind due to damage resulting from improper use
are excluded. The user of the device bears the sole risk.

Important when unpacking

To unpack the device, please proceed as follows:
Take the device out of the box. Remove all packaging and any
stickers on the device. Do not remove the type plate!

Before first use

Thoroughly clean all individual parts with washing-up liquid
and warm water to free them from any production residues.
See also "Cleaning".
Requirements for the installation
location
For safe and error-free operation of the device, the following
must be observed when setting up:
The device location / the surface on which the device stands
must be level (horizontal), stable, non-slip and heat-resistant
and have sufficient load-bearing capacity for the device. Do not
place the device in a hot, wet or humid environment.
Select the installation location so that children cannot reach
moving parts. Also keep loose parts like the blade of the meat
mincer out of the reach of children. The device is also not
intended for installation in a wall or a built-in cabinet.
The socket must be easily accessible so that the connection
cable can be pulled out quickly in an emergency.
EN
19