Sharp ER-A610 Programmierhandbuch Seite 147

DISPLAY FORMAT
SEND F1201111
Note 1: The table file (file No. 700) cannot extend over multi-
ple media (floppy disks).
Note 2: If the floppy disk contains any file that is the same in
file name as the file to be created in a file creation
step 2 or 4 above, "FILE NAME SEND?" appears on
the ECR display.
To create the file, it is necessary to enter the TL key;
and otherwise it is necessary to enter the
Those file extending over multiple media (floppy disks) can
be received by performing the ordinary receive operation
(see 4-6)).
4-6) Receiving file data from the ER-02FD
This function causes the ECR to receive file data from the ER-02FD.
Procedure for PGM job #898
898 X (FILE No.)
The ECR can receive specified files from a floppy disk in the ER-
02FD connected to it when the above job is performed.
If any specified file is not present in the ECR, a "ENTRY ERROR"
error occurs.
PRINT FORMAT
When the send operation has successfully terminated:
#0895 ∗Π Γ Μ ≤ ∗
ρεχει ϖε
φ1100111. δατ
When the send operation has been canceled:
#0898 ∗Π Γ Μ ≤ ∗
ρεχει ϖε
φ1100111. δατ ερρορ4
DISPLAY FORMAT
During a Receive operation
RECEIVE F1100111
∗ If ECR memory space is full when ECR is receiving the data, a
"MEMORY FULL" error occurs. (The data received before the
"MEMORY FULL" error occurs is valid.)
PRINT FORMAT
When "MEMORY FULL" error occurs:
#0895 ∗Π Γ Μ ≤ ∗
ρεχει ϖε
φ010ξξξξ. δατ
µεµορψ φυλλ
⊗
TL
JOB CODE/MODE TITLE
οκ
ERROR4
(Specified file is not present.)
JOB CODE/MODE TITLE
οκ
4-7) Presetting and reading of stack files
The presetting of stack files enables those files to be loaded and
dumped with a single job.
This presetting is of addition type. The following two kinds of preset-
ting are available.
Stack file presetting 1
PGM2 MODE
key.
887
Stack file presetting 2
PGM2 MODE
888
PRINT FORMAT
When "MEMORY FULL" error occurs:
#0887 ∗Π Γ Μ ≤ ∗
φ1401111. δατ
Reading of preset stack files
(PGM2 MODE)
887 X
PRINT FORMAT
#0887 ∗Π Γ Μ ≤ ∗
∗887
∗888
4-8) Sending and receiving of stack files
Those files that have been preset by jobs #887 and #888 can be sent
and received by using the following procedures:
Procedures for sending and receiving those files preset by presetting
1
(Job#887)
™ 58 ™
X
X (FILE No.) ST TL
For full deletion of atack files
TL
(Up to 20 files can be preset)
X
X (FILE No.) ST TL
TL For full deletion of atack files
(Up to 20 files can be preset)
JOB CODE/MODE TITLE
φ1101111. δατ
Stack file preset
φ1201111. δατ
φ1301111. δατ
−−−−
Individual deletion of stack file
TL
JOB CODE/MODE TITLE
φ1100111. δατ
φ1200111. δατ
φ1300111. δατ
φ2101111. δατ
φ2201111. δατ
φ2301111. δατ
For individual deletion
atack files
For individual deletion
atack files