Product Familiarisation; Unpacking Your Tool; Before Use - Silverline 102580 Bedienungsanleitung

GB

Product Familiarisation

1 Mains Cable Storage
2 Lance & Hose Bracket
3 Lock Off Lever
4 Trigger
5 Lance
6 Lance Hose Connecter
7 Lance Extension Bayonet Fitting
8 Lance Extension
9 Lance Bayonet Socket
10 Lance Nozzle
11 Hose Lance Connectorr
12 Quick Connector
13 High Pressure Hose
14 High Pressure Hose Connector
15 Lance Detergent Dispenser
16 Cleaning Pin
17 High Pressure Hose Socket
18 Water Inlet Connector
19 On/Off Switch

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all
its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Assembly
• Do not connect the pressure washer to the water or electrical supply until
fully assembled and ready for use
• Remove all packaging materials from the product
Lance
• Assemble Lance (5) by connecting Lance Extension (8). Connect Lance
Extension Bayonet Fitting (7) to Lance Bayonet Socket (9) by inserting,
rotating and then releasing so the bayonet fitting is locked in the groove
of the bayonet socket
Notes:
• If using the Lance Detergent Dispenser (15) fit to the Lance Bayonet
Socket (9) instead of the Lance Extension (8)
• If the Lance comes in two parts with the Lance (5) and tube with the
Lance Bayonet Socket (9) separate simply connect together with the
bayonet fittings
• Do not attempt to fit the Lance Extension (8) or Lance Detergent
Dispenser (15) directly into the bayonet fitting on the lance handle. The
fittings are a different size
6
All manuals and user guides at all-guides.com
High pressure hose
1. Remove the plastic cap from the Lance Hose Connector (6) if fitted
2. Carefully cut and remove cable ties around the hose (making sure not
to damage the hose surface), then uncoil hose
3. Attach Hose Lance Connector (11) to the Lance Hose Connector (6).
Screw the fittings together until tight
4. Remove the plastic cap from the High Pressure Hose Socket (17)
5. Attach the High Pressure Hose Connector (14) to High Pressure Hose
Socket (17). Screw the fittings together until tight
Warning: If the high pressure hose is damaged it can burst and cause
injury. A damaged hose must be replaced, not repaired. Inspect regularly
and prevent the hose from coming into contact with sharp objects or rough
surfaces
Connecting to water supply
Warning: When connecting a pressure washer to a normal house water
supply it is important a non-return valve is fitted to the hose (also called
a backflow preventer) to ensure the pressure washer cannot contaminate
your water supply if there is a backflow.
1. Remove the plastic cap from the Water Inlet Connector (24)
2. Check the filter inside the water inlet connector is clear of debris or
any other material. Over time debris may build up and the filter will
need to be checked regularly and any debris build-up removed
3. Fit the Quick Connector (18) to the Water Inlet Connector (24) and
tighten by hand only
4. Connect a hose from the water supply to the fitted quick connector
Notes:
The specification lists suitable water inlet pressures. A typical normal UK
household water supply can range from 1-8 Bar pressure but 2-5 Bar is
more typical. Do not exceed the maximum water pressure stated in the
specification.
NOTE: If you do not know or are unable to measure the water pressure,
keep the pressure low to prevent damage to the pressure washer. Aim
to set the pressure at mid-point between the lowest and highest water
pressure accepted by the pressure washer. If preferred, a third party water
pressure gauge is available that connects directly to the tap. This will allow
the water pressure to be set more accurately.
• Do not connect to a hot water supply. This will prevent the pump from
cooling and may damage the seals over time
• It is important that a good water connection is maintained while
operating a pressure washer, as the pump will be damaged if run without
water. Make sure the connections are secure before turning on the
pressure washer

Before Use

• Always check that all parts and attachments are secure, and that hoses
are not kinked or obstructed
• Always wear appropriate personal protective equipment. Use of this
machine requires safety goggles and waterproof clothing
• Always use an RCD when connecting a pressure washer to the mains
with a tripping current no more than 30mA and a delay in operating of
no more than 30ms
• Make sure any mains connection points are out of reach of the pressure
washer water spray, or any water that may collect on the surface around
where you are spraying
• If you use a mains extension cable be cautious about where the cable
is joined to the pressure washer mains cable. This must not be exposed
to water. Ideally extension cables should not be used unless designed to
withstand water ingress with water tight connections
• Always use the pressure washer vertically