Seite 1
MID Erstausrüster-Sets für Wärme- und Kältezähler PolluCom E, PolluStat, PolluTherm, PolluWatt Duo II Montageanleitung 1. Verwendung und Bestandteile der MID Erstausrüster-Sets Diese Montageanleitung gilt für folgende MID Erstausrüster-Sets, die für die Wärme- und Kältezähler PolluCom PolluStat, PolluTherm PolluWatt Durchflusssensoren Verschraubungsausführung verwendet werden. 1.1.
MID Erstausrüster-Sets für Wärme- und Kältezähler PolluCom E, PolluStat, PolluTherm, PolluWatt Duo II Montageanleitung Für Zähler PolluStat, PolluTherm und PolluWatt Duo II mit Durchflusssensoren in Flanschausführung sind die Kugelhähne oder Tauchhülsen sowie die Passstücke separat zu bestellen. 2. Sicherheitshinweise Wichtige Hinweise zur Vermeidung von Personen- und/oder Sachschäden: ...
MID Erstausrüster-Sets für Wärme- und Kältezähler PolluCom E, PolluStat, PolluTherm, PolluWatt Duo II Montageanleitung Abb 1: Messung im Sekundärkreis nach Beimischung Abb 2: Messung im Primärkreis vor der Beimischung In der Regel sollte der Wärmemengenzähler im Sekundärkreis nach der Beimischung eingebaut werden. Bitte beachten Sie hinsichtlich Einbaulage und Baulänge des Durchflusssensors auch die Einbau- und Betriebsanleitungen der jeweiligen Zähler.
Seite 4
MID Erstausrüster-Sets für Wärme- und Kältezähler PolluCom E, PolluStat, PolluTherm, PolluWatt Duo II Montageanleitung 3.4 Einbaubeispiele Kälterer Strang Wärmerer Strang (Vorlauf) (Vorlauf) Wandadapter für Rechenwerk Kälterer Strang Wärmerer Strang (Rücklauf) (Rücklauf) Abb 3: PolluCom E in einer Heizungsanlage Abb 4: PolluCom EX/S in einer Kälteanlage Abb 5: Einbau Temperaturfühler im Kugelhahn Materialnummer: 28505041 Stand: 007-03-2019...
Seite 5
MID starter kit for heating and cooling meters PolluCom E, PolluStat, PolluTherm, PolluWatt Duo II installation manual 1. MID starter kit application and components This assembly instruction applies to the following MID starter kit sets which are used for PolluCom E, PolluStat, PolluTherm and PolluWatt Duo II heating and cooling meters with screw connection flow sensors.
MID starter kit for heating and cooling meters PolluCom E, PolluStat, PolluTherm, PolluWatt Duo II installation manual For PolluStat, PolluTherm and PolluWatt Duo II with flanged flow sensors the ball valves, sensor pockets and spool pieces have to be ordered separately. 2.
Seite 7
MID starter kit for heating and cooling meters PolluCom E, PolluStat, PolluTherm, PolluWatt Duo II installation manual Fig.1: Measurement in secondary circuit after admixing Fig.2: Measurement in primary circuit before admixing Usually heating meters should be installed in the secondary circuit after admixing. Concerning installation position and length of the flow sensor please also note the installation manual and instruction of the respective meter.
MID starter kit for heating and cooling meters PolluCom E, PolluStat, PolluTherm, PolluWatt Duo II installation manual 3.4 Installation examples Colder line Warmer line (supply pipe) (supply pipe) Wall adapter for calculator Colder line Warmer line (return pipe) (return pipe) Fig.3: PolluCom E in a heating system Fig.4: PolluCom EX/S in a cooling system Fig.5 : installation of a temperature sensor in a ball valve...