Makita DBO140 Bedienungsanleitung Seite 5

ENGLISH (Original instructions)
SPECIFICATIONS
-1
Orbits per minute(min
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for the sanding of large surface of
wood, plastic and metal materials as well as painted
surfaces.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841:
Model DBO140
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model DBO180
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
Model
Paper size
) Low speed
Middle speed
High speed
Dimensions
Net weight
D.C.14.4 V Model
D.C.18 V Model
) : 78 dB (A)
pA
) : 77 dB (A)
pA
DBO140
175 mm x 123 mm x 153 mm
1.3 - 1.6 kg
D.C. 14.4V
BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841:
Model DBO140
Work mode : sanding metal plate
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DBO180
Work mode : sanding metal plate
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
5 ENGLISH
DBO180
125 mm
7,000
9,500
11,000
1.4 - 1.7 kg
D.C. 18V
2
) : 2.5 m/s or less
h
2
2
) : 2.5 m/s or less
h
2