Werbung
Verfügbare Sprachen
Verfügbare Sprachen
O P E R A T I N G I N S T R U C T I O N S
Additional remote control, 433 MHz
Item no. 55 74 91
Intended use
The product is used as an additional hand-held radio transmitter for the suitable radio-controlled switch set
(available separately).
Always observe the safety instructions and all other information included in these operating instructions!
This product complies with the applicable national and European requirements. All names of companies and
products are the trademarks of the respective owners. All rights reserved.
Package content
• Hand-held radio transmitter
• 12 V battery (Type 23 A)
• Operating instructions
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe these safety
instructions! We do not assume any liability for any resulting damage!
We shall not accept liability for damage to property or personal injury caused by incorrect
handling or non-compliance with the safety instructions! In such cases, the warranty will
be null and void.
• Unauthorised conversion and/or modifi cation of the product is not allowed for safety and
approval reasons (CE).
• The product is not a toy and should be kept out of the reach of children!
• Do not use this product in hospitals or medical institutions. Although the product emits only
relatively weak radio signals, these may lead to the malfunction of life-support systems. The
same may also apply to other areas.
• The product must only be used in dry interiors, it must not get damp or wet.
• Do not leave packaging material carelessly lying around, since it could become a dangerous
plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or accidental falls, even
from a low height.
General Battery Instructions
• Batteries should be kept out of the reach of children.
• Do not leave batteries lying around in the open; there is a risk of them being swallowed by children or pets.
If they are swallowed, consult a doctor immediately.
• Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suitable protective
gloves.
Liquids leaking from batteries are very chemically aggressive. Objects or surfaces coming into contact with
these liquids might be considerably damaged. Thus, store batteries in a suitable location.
• Batteries/rechargeable batteries must not be short-circuited, opened or thrown into a fi re. There is a risk of
explosion!
• Do not recharge normal, non-rechargeable batteries, due to risk of explosion!
• Please pay attention to the correct polarity (plus/+ and minus/-) when inserting the battery.
Controls
A
Control-LED (lights up on use of buttons)
B
Keypad for switching channels 1 to 4 (left column
"ON" = on, right column "OFF" = off)
C
Coding switch I, II, III, IV for one of the four
address codes
D
Battery compartment
Inserting/Replacing the Battery
Open the battery compartment (D) on the back of the hand-held radio transmitter and insert a type "23A"
battery with the correct polarity (observe imprint in the battery compartment or the fi gure). Close the battery
compartment.
The batteries need to be replaced if the range of the hand-held radio transmitter is signifi cantly reduced or
the control-LED (A) no longer lights when the buttons are used.
Setting the Address Codes
One of the four address codes (I, II, III, IV) can be set on both the hand-held radio transmitter and the radio-
controlled switch socket. Therefore, up to four identical radio-controlled switch sets can be operated without
infl uencing each other.
Select one of the address codes (I, II, III, IV) on the hand-held radio transmitter via the sliding switch (C). Set
exactly the same address code on the radio-controlled switch socket(s).
If you set a different code on the hand-held radio transmitter and the radio- controlled switch
socket, the switch socket will not react to the switching commands on the hand-held radio trans-
mitter!
For the settings of the radio-controlled switch socket please refer to its operating instructions.
www.conrad.com
Version 07/13
A
1
2
3
B
4
ON
OFF
-
+
Operation
If you press the "ON" button of the corresponding switching channel (1, 2, 3 or 4), the respective radio-
controlled switch socket is activated. The red control LED on the radio-controlled switch socket has to light
up and the load connected to it will be switched on.
The radio-controlled switch socket and the load connected to it are switched off using the "OFF" key of the
corresponding switching channel.
Please consult the instruction manual for further information on the radio-controlled switch socket.
Maintenance and Cleaning
The product is maintenance-free for you; never open/dismantle it (except for inserting/replacing the batteries
or rechargeable batteries as described in these operating instructions).
Only clean the product with a soft, clean, dry cloth. Never use aggressive cleaning agents or chemical solu-
tions since these might damage the surface of the casing or impair the operation.
Range
The transmission range of the radio signals, between the hand-held transmitter and the radio-controlled
switch sockets, is up to 30 m under optimum conditions.
This value, however, is the so-called "open space range" (the range when the transmitter and
receiver are visible to each other, without disturbing infl uences).
In practical operation, however, there are walls, ceilings of rooms etc. between the transmitter
and the receiver, which reduce the range accordingly.
Due to the different infl uences on the radio transmission, no specifi c range can be guaranteed.
However, trouble-free operation is usually possible in a single family house.
The range can sometimes be considerably reduced due to:
• Walls, reinforced concrete ceilings
• Coated/metallised insulated glass
• Proximity to metallic & conductive objects (e.g. heating elements)
• Proximity to human bodies
• Broadband interferences, e.g. in residential areas (DECT telephones, mobiles, radio-controlled head-
phones, radio-controlled speakers, other radio-controlled weather stations, baby phones etc.)
• Proximity to electric motors, transformers, power-supply units, computers
• Proximity to badly shielded or uncovered computers in use or other electrical appliances
Disposal
a) General instructions
Please dispose of the device, when it is no longer of use, according to current statutory require-
ments.
Remove the inserted battery and dispose of it separately from the product.
b) Normal and Rechargeable Batteries
As the end user, you are required by law (Battery Regulation) to return used batteries and rechargeable
batteries. Do not dispose of used batteries in the household waste!
Batteries/rechargeable batteries that contain hazardous materials are labelled with the follow-
ing symbols to indicate that disposal in the household waste is forbidden. The symbols of the
relevant heavy metals are: Cd=Cadmium, Hg=Mercury, Pb=Lead (name written on the battery/
rechargeable battery, e.g. under the rubbish bin symbol on the left).
You can return your used batteries/rechargeable batteries free of charge at the offi cial collection points of
your community, in our stores, or at places where batteries or rechargeable batteries are sold.
You thereby fulfi l your statutory obligations and contribute to the protection of the environment.
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this product con-
forms to the fundamental requirements and the other relevant regulations of the directive 1999/5/EC.
The Declaration of Conformity for this product can be found at www.conrad.com.
Technical Data
C
Power supply ...............................1x 12 V battery, type "23A"
Transmission frequency...............433 MHz
Address codes .............................4 (to be set via the sliding switch I, II, III, IV)
Switching channels ......................4 (each with "ON"/"OFF"-button)
D
Range ..........................................up to 30 m (open space, see chapter "Range")
LED ..............................................lights up briefl y, when the buttons are used
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.
Werbung
