IKEA NUVARANDE Handbuch Seite 9

Operating modes
The appliance provides four operating modes
(COMFORT; ECO NIGHT; CHRONO; TOWEL DRYER).
Each of these modes allows the user to heat the
environment in the most suitable way with respect to
their needs.
COMFORT mode
ECO NIGHT mode
CHRONO mode
TOWEL DRYER
mode
Turning on/standby
To turn on the towel dryer, press the
on Key and you will hear a double
beep signal alert that the towel dryer
is on.
To turn off, press the same Key and the
"Stby" icon will appear on the display.
A prolonged beep signal alert will
sound that the towel dryer is off.
The "STANDBY" mode signals that all
the operating modes are suspended
but the appliance is powered and
waiting for command reception. This
implies that it is consuming extremely
low electricity (less than 0.5 W as
required by Ecodesign regulation).
Turning on for the first time
When you turn the appliance on for the first time, you
will be prompted to set the following parameters:
Days of the week: adjust the day of
the week by using the "+"and "-"keys
(1=MON, 2=TUE,...7=SUN), then confirm
by pressing the "MODE" selection key.
Hours: after selecting the days of the
week, the hour starts flashing. For the
days of the week, adjust the hours by
using the "+"and "-"keys and confirm
with the "MODE" selection key.
The "COMFORT" temperature is
set by the user.
The "ECO NIGHT" temperature
is set by the user. The set
temperature must not be
higher than the "COMFORT"
one.
In this mode, you can select
one of the three preset
"CHRONO"-thermostat
programmes ("P1" or "P2") or
customise the programme "P3"
daily and weekly.
This function reduces
consumption by focusing most
of the heat just on where the
towel is located.
Minutes: after selecting the hours, the
minutes start flashing. For the hours,
adjust the minutes by using the "+"and
"-" keys and confirm with the "MODE"
selection key.
By default, the temperature difference
between "COMFORT" mode and "ECO
NIGHT" mode is 3°C. The difference
can be varied from 2°C to 4°C by using
the "+" and "-"keys.
If there is a need to change the time or change the
temperature difference between "COMFORT" mode
and "ECO NIGHT" mode:
Put the thermostat on "STANDBY" mode. Press
the "+"and "-" buttons simultaneously for at least 5
seconds. The thermostat will go into day, hour and
"ECO NIGHT/COMFORT" offset mode.
Press the "+"and "–" keys to change day, hours,
minutes and finally the offset (the temperature
difference between "ECO NIGHT" and "COMFORT"
mode). For each step, press "MODE" to confirm. At
the end of this procedure, the thermostat returns to
"STANDBY" mode. After turning on the thermostat,
you will notice the new settings.
Operating modes
Press the "MODE" key to select the desired operating
mode. The icon listed in the Table 1 on the LCD will
show the selected operating mode.
COMFORT (traffic light colour led: red, yellow and
green)
The "COMFORT" temperature set is the temperature
set by the user.
Press the "MODE" selection key until the "COMFORT"
icon appears on the LCD.
Choose the desired temperature set by using the "+"
or "-" keys.
The temperature can be chosen within the interval
between 7°C and 30°C when the element is powered
and different LED coloured lights flash according to
the range temperature.
Selected temperature below 19°C: the green LED light
flashes. When the desired temperature of 19°C is
selected, the green LED light stop flashing and stays
green.
Selected temperature between 19°C and 24°C: the
yellow LED light flashes. When the temperature is
reached, the yellow LED light stop flashing and stays
yellow.
Selected temperature above 24°C the red LED light
flashes. When the temperature is reached, the red LED
stop flashing and stays red.
ECO NIGHT (Light-blue LED light)
In "ECO NIGHT" mode the temperature set must not be
higher than the "COMFORT" temperature set.
By default, the temperature difference between
"COMFORT" and "ECO NIGHT" is 3°C. This difference
can be changed from 2°C to 4°C as described in the
chapter Turning on for the first time.
9