MaxPro PROFESSIONAL MPRH900/26V Bedienungsanleitung Seite 5

•This tool should not be used by people under the age of 16 years
•If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediatelyswitch
off the tool
•Use suitable detectors to find hidden utility lines or call the local utility company for assistance
(contactwith electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or an electrical shock)
•Hold the power tool only by the insulated gripping surfaces when performing an operation where
theaccessory may contact hidden wiring or its own power cord (contact with a "live" wire will also make
exposed metal parts of the power tool "live" and shock the operator)
•Dust from material such as paint containing lead, some wood species, minerals and metal may beharmful
(contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the
operator or bystanders); wear a dust mask and work with a dust extraction device when connectable
•Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in
conjunctionwith additives for wood conditioning; wear a dust mask and work with a dust extraction
device when connectable
•Follow the dust-related national requirements for the materials you want to work with
•Do not work materials containing asbestos (asbestos is considered carcinogenic)
•If the cord is damaged or cut through while working, do not touch the cord, but immediately
disconnectthe plug
•Never use the tool when cord is damaged; have it replaced by a qualified person
•Always check that the supply voltage is the same as the voltage indicated on the nameplate of the
tool(tools with a rating of 230V or 240V can also be connected to a 220V supply)
•Be aware of the forces that occur as a result of jamming (especially when drilling metals); always
useauxiliary handle and take a secure stance
•Always disconnect plug from power source before making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal
ofthe plug
•If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not
leftunattended
SYMBOLS
Read the manual
Warning
Double insulation
Wear eye protection
OPERATING INSTRUCTION
• On/off 11 (Fig.1)
(Fig.2)
• Maximum speed control
With wheel 10 the maximum speed can be adjusted from low to high (1-6)
• Activating rotation switch 8 (Fig.3)
- Press button 9 to unlock switch 8
- Turn switch 8 along the bottom side to position "
4
Wear ear protection
Wear dust mask
Do not dispose of old appliances in the
household garbage
Keep your hands and feet away from all
opening
" until it snap-locks
GB
!do not turn switch 8 along the upper side
!start working only when switch 8 is locked
• Activating hammer switch 9 (Fig.3)(Fig. 8 ) 8
- Turn switch 9 along the upper side to position "
!do not turn switch 9 along the bottom side
• Operating the tool (Fig.3)(Fig. 8 ) 8
!select operating mode only when tool is switched off and plug is disconnected
-for impact drilling set switch 8 in position "
-for normal drilling as well as for screw driving set switch 8 in position "
and use chuck
-the hammer mechanism is activated by applying a slight pressure on the tool when the drill bit is in contact
with the work piece
-best impact drilling results can be obtained by only a slight pressure on the tool needed to keep the
automatic clutch engaged; drilling performance will not improve by applying more pressure on the tool
• Chiseling (Fig.6)
!select operating mode only when tool is switched off and plug is disconnected
-first set switch 9 as well as switch 8 in position "
-rotate chisel into desired position
-then maintain switch 9 in position " ", but set switch 8 in position "
• Mounting chuck (Fig.7)
!clean and lightly lubricate the SDS+ adapter before insertion
- pull back locking sleeve 2 and insert adapter in SDS+ chuck while turning and pushing it until it engages;
the adapter locks in position automatically
- pull adapter to check whether it is locked correctly
• Changing bits!
!clean and lightly lubricate the SDS+ accessory before insertion
- pull back locking sleeve and insert accessory in SDS+ chuck while turning and pushing it until it engages;
the accessory locks in position automatically
- pull accessory to check that it is locked correctly
- remove accessory by pulling back locking sleeve 2
!the SDS+ accessory requires freedom of movement which causes eccentricity when tool is off-load;
however, the accessory automatically centres itself during operation without affecting drilling precision
!only use sharp bits/chisels
!do not use bits/chisels with a damaged shank
• Safety clutch
If the accessory gets jammed, the drive to the spindle is interrupted (causing a rattling noise)
-immediately switch off tool
- remove the jammed accessory
- switch on tool again
• Adjusting drilling depth 5 (Fig.4)
-this tool is equipped with carbon brushes which pop up automatically when worn, thus preventing the
motor from being damaged
-when the tool stops unexpectedly, send it to your dealer or the nearest MAXPRO service-station for having
the brushes replaced
(Fig.5)
• Holding and guiding the tool
!while working, always hold the tool at the grey-coloured grip area(s)
-always use auxiliary handle 6 (can be adjusted as illustrated)
- keep the ventilation slots uncovered
- do not apply too much pressure on the tool; let the tool do the work for you
APPLICATION ADVICE
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an edge of wood, pre-drill a hole in order to avoid
cracking of the wood
"
" and switch 9 in position " "
" and switch 9 in position "
"
"
GB
"
5