Safty Instructions - Dexter power AC50V Originalbetriebsanleitung

5. Safety instructions
m Attention! The following basic safety meas­
ures must be observed when using electric tools
for protection against electric shock, and the risk of
injury and fire. Read all these notices before using
the electric tool and keep the safety instructions for
later reference.
Safe work
Keep the work area orderly
1
Disorder in the work area can lead to acci­
–
dents.
Take environmental influences into account
2
Do not expose electric tools to rain.
–
Do not use electric tools in a damp or wet en­
–
vironment. There is a risk of electric shock!
Make sure that the work area is well­illuminat­
–
ed.
– Do not use electric tools where there is a risk
of fire or explosion.
Protect yourself from electric shock
3
Avoid physical contact with earthed parts
–
(e.g. pipes, radiators, electric ranges, cooling
units).
Keep children away
4
Do not allow other persons to touch the equip­
–
ment or cable, keep them away from your
work area.
Securely store unused electric tools
5
Unused electric tools should be stored in a
–
dry, elevated or closed location out of the
reach of children.
Do not overload your electric tool
6
They work better and more safely in the speci­
–
fied output range.
Wear suitable clothing
7
Do not wear wide clothing or jewellery, which
–
can become entangled in moving parts.
– Rubber gloves and non­slip shoes are recom­
mended when working outdoors.
Tie long hair back in a hair net.
–
Do not use the cable for purposes for which it is
8
not intended
Do not use the cable to pull the plug out of
–
the outlet. Protect the cable from heat, oil and
sharp edges.
Take care of your tools
9
Keep your compressor clean in order to work
–
well and safely.
Follow the maintenance instructions.
–
Check the connection cable of the electric tool
–
regularly and have it replaced by a recognised
specialist when damaged.
Check extension cables regularly and replace
–
them when damaged.
Pull the plug out of the outlet
10
During non­use of the electric tool or prior to
–
maintenance and when replacing tools such
as saw blades, bits, milling heads.
Avoid inadvertent starting
11
Make sure that the switch is switched off when
–
plugging the plug into an outlet.
Use extension cables for outdoors
12
Only use approved and appropriately identi­
–
fied extension cables for use outdoors.
Only use cable reels in the unrolled state.
–
Remain attentive
13
Pay attention to what you are doing. Remain
–
sensible when working. Do not use the elec­
tric tool when you are distracted.
Check the electric tool for potential damage
14
– Protective devices and other parts must be
carefully inspected to ensure that they are
fault­free and function as intended prior to
continued use of the electric tool.
Check whether the moving parts function
–
faultlessly and do not jam or whether parts are
damaged. All parts must be correctly mounted
and all conditions must be fulfilled to ensure
fault­free operation of the electric tool.
Damaged protective devices and parts must
–
be properly repaired or replaced by a recog­
nised workshop, insofar as nothing different is
specified in the operating manual.
– Damaged switches must be replaced at a
customer service workshop.
Do not use any faulty or damaged connection
–
cables.
Do not use any electric tool on which the
–
switch cannot be switched on and off.
Have your electric tool repaired by a qualified
15
electrician
This electric tool conforms to the applicable
–
safety regulations. Repairs may only be per­
formed by an electrician using original spare
parts. Otherwise accidents can occur.
Important!
16
– For your own safety you must only use the
accessories and additional units listed in the
operating instructions or recommended or
specified by the manufacturer. The use of
mounted tools or accessories other than those
recommended in the operating instructions
or catalog may place your personal safety at
risk.
17 Noise
Wear ear muffs when you use the compres­
–
sor.
Replacing the power cable
18
To prevent hazards, leave the replacement of
–
damaged power cables strictly to the manu­
facturer or a qualified electrician. There is a
risk of electric shock!
Inflating tires
19
Directly after inflating tires, check the pres­
–
sure with a suitable pressure gauge, for exam­
ple at your filling station.
GB 23