Technical Data; Noise/Vibration Information; Changing The Tool - Bosch GKF 600 Professional Originalbetriebsanleitung

(13) Collet
(14) Tool holder
(15) Open-ended spanner (17 mm)
(16) Knurled screw for attachment of side stop
(17) Parallel guide
(18) Wing bolt for parallel guide
(19) Roller guide
(20) Wing bolt for locking of the horizontal alignment
(21) Wing bolt for horizontal alignment of the roller guide
(22) Guide roller
a)
(23) Base cover sleeve

Technical data

Edge router
Article number
Rated power input
No-load speed
Compatible collets
Weight according to EPTA‑Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-17.
Typically the A-weighted noise level of the power tool are:
84 dB(A); sound power level 95 dB(A). Uncertainty
K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-17: a
2
K = 1.5 m/s .
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Bosch Power Tools
(24) Tilt base
(25) Wing bolt for angle adjustment
(26) Scale for routing angle adjustment
(27) Handle for the guide plate
(28) Extraction guard
(29) Extraction adapter
(30) Guide plate with handle and extraction adapter
(31) Nut for adjustment of the tensioning force
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
min
mm
inches
kg
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Fitting
Pull the plug out of the socket before carrying out any
u
work on the power tool.
2
= 4.5 m/s ,
h

Changing the tool

Wearing protective gloves while fitting and changing
u
router bits is recommended.
Original router bits from the extensive range of Bosch ac-
cessories are available from your specialist dealer.
Removing the Routing Base (see figure A)
Before fitting a router bit, you must first separate the routing
base (2) from the drive unit (1).
Open the clamping lever (10) and turn the routing base (2)
with the mark
Pull the drive unit upwards as far as it will go.
Turn the drive unit anticlockwise as far as it will go and pull it
out of the routing base.
Changing the collet (see figure B)
Depending on the router bit used, you may have to change
the cap nut with the collet (5) before fitting the router bit.
a)
a)
a)
a)
GKF 600
3 601 F0A 1..
W 600
−1
33000
6 | 8
–
1.5
/II
to the symbol on the drive unit (1).
1 609 92A 57W | (01.04.2021)
English | 15
a)
GKF 600
3 601 F0A 16.
3 601 F0A 17.
600
33000
–
¼
1.5
/II