Maintenance And Care - KIKKA BOO WOODY Gebrauchsanweisung

Congratulations on your purchase. To ensure maximum protection and optimum comfort for your child, it is essential that you read through the entire manual
carefully and follow all instructions. Read these instructions carefully before assembly and use and keep for future reference. The child may be hurt if you do not
follow these instructions.
WARNINGS
• This highchair is intended for children able to sit up unaided (usually around 6 months) and up to 3 years or a maximum weight of 15kg.
• This highchair can be used as a junior chair. Junior chair mode is suitable from 36 months (3 years) to approx 5 years.
Be aware of the risk of open res and other sources of strong heat, such aselectric bar res, gas res etc. in the vicinity of the highchair.
• Never leave the child unattended. Always keep child in view while in the highchair.
• Position the highchair on a at, even and horizontal oor and do not elevate the highchair on any structure or table.
• FALLING HAZARD: Prevent your child from climbing on the product.
• Be aware of the risk of tilting when your chiId can push its feet against a table or any other structure.
• DO NOT allow the child to climb or stand on or inside of this highchair. lt is not a step stool or ladder.
• To reduce the risk of injury, position the highchair away from furniture, walls, hot surfaces and liquids, window covering cords and electrical cords and position
the highchair away from furniture when the highchair is being used at a table with the tray removed.
• The highchair should only be used once the child is capable of reliably and consistently sitting upright. This is usually around 6 months of age.
• Your child MUST ALWAYS be secured with the harness.
• Do not use the highchair if any part is broken, torn or missing. Do not use the highchair unless all components are correctly tted and adjusted.
• Regularly check all connections to ensure they are tight.
• Keep the plastic packaging away from children to avoid danger of su ocation.
Conforms to EN 14988:2017
I PARTS LIST
Please check every part and follow up the assembling steps for complete baby high chair. Do not use the product if any part is broken or missing.
1. Chair Seat (1 pcs); 2. Tray (1 pcs); 3. Foot rest(1 pcs); 4. Leg support(2 pcs); 5. Upper Legs (4 pcs); 6. Lower legs (4 pcs); 7. Screw (5 pcs), Nuts (5 pcs),Tools (1 pc),
Anti-slip pads for junior chair (4 pcs);
II. ASSEMBLY (Stage 1)
1. Assemble the four legs by joining the upper and lower legs according to the same marks (A+A, B+B, C+C, D+D). (Fig-1)
2. Screw the four legs into the seat bottom. (Fig-2, Fig-3) Do not screw too tight for next step.
3. Install the two leg supports and footrest by using screws ' A ' , 'B' , 'C' and 'D' nuts. (Fig-4)
a. Begin by joining the two leg supports using screw 'C' and a nut through the center hole. The holes on the leg supports should extend downwards.
b. Next, install the footrest onto the front side of chair. Screws ' A ' (the two longer screws) needs to pass through the foot rest, then the chair leg and the leg
support before securing with a nut. The leg support with the "O" marking should be on the left-hand side. (Fig-5). Adjust the chair leg by twisting it to align hole
for the screw. Finally, attach the leg supports to the back legs using screws 'B' (the two shorter screws) and remaining nuts.
4. Put the tray on the handrail. (Fig-6)
5. Press the tray to make sure it is securely locked in place. (Fig-7)
6. Make sure the seat cover is put in right place in seat. (Fig-6) Check high chair again to make sure everything is OK before use. The harness must always be used
and correctly tted. Most injuries from highchairs are caused by falls.
The way to change high chair to junior chair ( Stage 2):
Remove the 5-point harness, the seat cover, the tray, the guardrail, the foot rest, the four lower legs and put on the four anti-slip pads to protect the upper legs
before use.

MAINTENANCE AND CARE

• Check the components of each part (screw / seat belt bayonet). For the safety of your baby, carry out regular inspections and repairs weekly. If there is any
abnormality, please replace it immediately or stop using.
• Avoid long-term storage in wet or high temperature environment; otherwise it will easily lead to damage and aging of parts, a ecting product life or potential
danger.
• Cleaning the cushion: Unfasten the safety belt. Wash it with warm water and dry it to avoid exposure under high temperature.
• Do not use bleach and strong acid/base liquid for cleaning the chair frame. Avoid contact with water in hardware parts, as corrosion will a ect the service
life of the product. The plastic and metal parts must be cleaned with a damp soft cloth and dried with dry soft cloth.
• Do not let the product exposed to the harmful e ect of external factors - direct sunlight, rain, snow or wind. This may lead to damage of the metal and plastic
part.
• Regularly check the various parts of the baby high chair weekly, contact and repair with supplier immediately if you have any questions.
• Avoid prolonged exposure under hot environment; otherwise it will promote the aging and functional decline of parts, fabric fading and other problems.
• When you are not using the product, store it at a dry and well ventilated place, not in dusty, humid premises with very high or very low room temperatures.
ENGLISH