Elko EP USS-ZM Anleitung Seite 3

ELKO EP, s.r.o.
Palackého 493
769 01 Holešov, Všetuly
Czech Republic
Tel.: +420 573 514 211
e-mail: elko@elkoep.com
www.elkoep.com
Made in Czech Republic
02-207/2016 Rev.: 3
Characteristics
• Independent switch units designed for fl exible controlling and switching of power
circuits.
• USS - "Do It Yourself" = it is possible to "click into" diff erent types of switches and
signalling units into the basic module.
• Units are delivered as components and confi gured by the user.
• 16 types of units: switches, push buttons, signal lights of diff erent colours includ-
ing fl ashing lights units are replaceable also for future (for example when an ap-
plication is changed, extended, etc...).
• Units are also replaceable in the future (for example when an application is
changed, extended, etc...).
• It is possible to place up to two units into one MODULE (for example 2x switch, 2x
signalling lights or combinations) = saves space in switchboard panels.
• 1-MODULE (90 x 17.6 x 64 mm / 3.5˝ x 0.7˝ x 2.5˝), DIN rail mounting.
• Operating temperature -20 °C to +55 °C (-4 °F to 131 °F).
• M3 screw with clamp terminals.
Means of assembly
A2
A3
A1
A11
A13
A12
04 1 2 3 5 6 7
0523
Positions
When only one position is engaged, the other position has to be blinded by a blind
fl ange USS-00.
While assembling it is necessary to click a switch or control light in the module USS-ZM
correctly. In case of insuffi cient connection of modules USS-ZM and USS-01-15, there is a
danger of transition resistance.
Orientation of switches, alternating switches, and control lights in USS-ZM modules
To ensure correct function of USS modules it is necessary to observe the correct Orienta-
tion of switches, alternating switches, and control lights.
a) Correct orientation of switches and alternating switches is valid for types USS-01-06.
b) Correct orientation of switches with back-light USS-07-09.
c) Correct orientation of control lights USS-10-15. The jog needs to point to the centre.
Dismounting of USS modules
The units are fi rmly seated after assembly, and unprofessional or careless disassembly
can lead to damage.
a) b) c)
0
1
I
0
II
USS
Controlling and signalling modules
Example of an order
Make your own device USS - easy and intelligent solution!
Warning
Device is constructed for connection for 1-phase main voltage or AC/DC 24 V and must
be installed according to norms valid in existing state. Installation, connection, setting
and servicing For right device protection should be fronted-end certain element. Before
starting installation must be main switch in position „SWITCH OFF" and device should be
out of voltage. Don´t install device to suppliers surcharge electro-magnetic interference.
By right installation of device is provide good air circulate to don´t pass maximal oper-
ating temperature,in case of higher ambient temperature and permanent working. For
installation and setting use screw-driver cca 2 mm. The device is full-electronic - installa-
tion should be eff ected according to this. Function without problems is too dependent
on previous type of transportation, storing and manipulation. In case of any vestige of
destruction, deformation, non-function or missing part, don´t install and made claim to
seller. Product may be ,after passing operating time, disassembled, recycled or puted on
protected tip. Connection according to the details in this direction. should be installed
by qualifi ed electrician staff only, who learn this instruction and functions of device
1 / 2
US USS-ZM + USS-11 + USS-03
EN