Kontrollrelais / Monitoring-relay – in-case – Thermistor Motorschutz / Thermistor protection – ICM
•
4 wählbare Funktionen
•
bis zu 6 PTC-Sensoren in Serie
•
Wählbare
angeschlossenen PTC-Sensor)
•
Kurzschlusserkennung
•
Automatischer, manueller oder extern
manueller Reset wählbar
•
Fehlerspeicherfunktion
•
Ausgangsstufe mit 2 Wechsler
•
LED Anzeige für Versorgungsspan-
nung,
Fehler,
in-case
Start- und Reaktionstimer
•
Gehäusebreite: 22,5mm klemmbar
Thermistor Motorschutz /
Thermistor protection
Artikel / Article
ICM 24Vac
ICM 115Vac
ICM
ICM 230Vac
ICM 400Vac
Spannungsbereich /
supply voltage variation
Zulässige Frequenz / frequency range
Einschaltdauer / duty cycle
Wiederholgenauigkeit / repeat accuracy
Ausgangsstufe /
output relay specification
HIQUEL GmbH
Ue/Ie AC-15*
Bairisch Kölldorf 266
Ue/Ie DC-13*
8344 Bad Gleichenberg
Lebensdauer / expected life time
Mechanisch / mechanical
AUSTRIA
Elektrisch / electrical
Schrauben / screws
Tel.: +43-(0)3159-3001
Anzugsdrehmoment / screw tight. torque
Fax: +43-(0)3159-3001-4
Arbeitsbedingungen /
Email: hiquel@hiquel.com
operating conditions
http://www.hiquel.com
01.01
Die
veröffentlichten
Beiträge
in
dieser
Unterlage
urheberrechtlich
geschützt.
Ihre
auch
nur
auszugsweise
Vervielfältigung und Verbreitung ist ausnahmslos nur mit
vorheriger schriftlicher Zustimmung des Herausgebers gestattet.
Die HIQUEL GmbH sowie die Autoren können für eventuell
vorhandene Fehler keine Haftung jeweiliger Art für fehlerhafte
Angaben und deren Folgen übernehmen.
This documentation and the accompanying illustrations are
copyrighted. This manual may not be copied in part or whole in
any form including electronic media without the written consent of
HIQUEL GmbH. The editors and publishers accept no responsibil-
ity for any inadvertent omission of entries or for typographical or
other errors herein. Nor can they be held responsible or liable for
consequences arising from any errors herein.
BESCHREIBUNG / FEATURES
•
4 selectable functions
•
Up to 6 PTC's in series
•
Testfunktion
(ohne
Selectable test-function (even without a
PTC's connected)
•
Short circuit detection
•
Automatic, manual or external reset
selectable
•
Alarm memory function
•
DPCO alarm relay
•
LED indicator for supply voltage, over-
Übertemperatur,
Kurzschluss,
temperature, short-circuit, alarm, output
Status
des
Ausgangsrelais,
relay status, start and reaction timer
•
22,5mm DIN rail mount housing
BESTELLDATEN / ORDERING INFORMATION
Nennspannung / nominal voltage
24Vac
115Vac
230Vac
400Vac
TECHNISCHE DATEN / SPECIFICATION
Nennspannung / nominal voltage
-20%..+10%
48 - 63 Hz
100%
<1%
max. 6A 230V~
24V/1,5A 115V/1,5A 230V/1,5A
24V/1A
2 Wechsler / DPCO
10 x 10
8 x 10
(at full rated voltage)
Pozidrive 1
0,6...0,8Nm
-20 bis +60 C
nicht kondensierend /
non condensing
ANSCHLUSS / CONNECTION DIAGRAM
sind
Copyright © 2008 by HIQUEL GmbH, Bairisch Kölldorf 266, 8344 Bad Gleichenberg, AUSTRIA. Alle Rechte vorbehalten, All rights reserved.
1W / 2,5VA
1W / 2,5VA
1W / 2,5VA
1W / 2,5VA
6
Schaltspiele / operations
4
Schaltspiele / operations
* EN 60947-5-1 VDE 0435
Spannungsversorgung OK /
Supply voltage OK
Fehlerauslöseverz. aktiv /
Alarm trip delay timer active
Kurzschluss / Short circuit
Übertemperatur /
Over-temperature
Fehleranzeige / Error indicator
Ausgangsrelais aktiv /
Output relay active
ZULASSUNG & KENNZEICHNUNG / TYPE APPROVAL INFORMATION
ABMESSUNGEN / DIMENSIONS (mm)
MONTAGE / MOUNTING
Die Montage ist mittels Schnapp-Befestigung
Lever open the spring clip on the base to
auf einer symmetrischen Hutschiene nach
mount device on a symmetrical DIN rail
DIN EN 50022 vorzunehmen. Die Geräte
according to DIN EN 50022. The devices are
sind für dicht an dicht Montage bei einer
suitable for mounting side by side without an
Umgebungstemperatur von -20 bis + 60°C
air gap with an ambient temperature range
geeignet.
from -20 to + 60°C.
Fehlerauslöseverzögerung /
Alarm trip delay time
Einschaltverzögerungszeit /
Reset-delay time
Reset- u. Test-Taster /
Reset and test-button
Funktionswahl /
Function setting
1