Operation - TFA 60.4518.08 Bedienungsanleitung

i
Note on radio-controlled time
The time is transmitted from an atomic clock near Frankfurt am Main by a DCF-77 (77.5 kHz)
frequency signal with a range of about 1,500 km. Your radio-controlled clock receives the signal,
converts it and always shows the exact time. The adjustment to Daylight Saving Time (summer/
winter time) is automatic.
During night-time, the atmospheric interference is usually less severe. A single daily reception is
adequate to keep the accuracy deviation under 1 second. In extreme cases, please place the unit
close to a window to improve reception.

2. Operation

Manual settings
Press and hold the MODE/SET button (Fig.2-A) for three seconds to enter the setting mode.
The first adjustable value flashes on the display.
Use the  or / button to make the desired setting.
Confirm with the MODE/SET button and go to the next setting.
The sequence is shown as follow:
- 24/12-hour format (default: 24Hr)
- DCF reception on/off (default: rcc on)
- Time zone -23/+23 (default: TIME ZONE 00)
- Day-of-week language: (default: German)
- Hours, minutes, seconds (setting only 00)
- Year, month, day
- Temperature unit °C/°F (default: °C)
- Alarm duration 1 or 2 minutes (default: 2)
Press and hold the  or /
button in the respective setting mode for quick setting. The
device will automatically quit the setting mode if no button is pressed for 15 seconds.
DCF reception
By default, the DCF reception is activated (RCC on) and after successful reception of the DCF
signal no manual adjustment is necessary.
Once the DCF time reception is deactivated (rcc of), the clock and date must be manually set. No
time zone will appear.
If the DCF reception is activated, the manually set time will be overwritten by the DCF time when
the signal is received successfully.
Time zone setting
In the setting mode you can make the time zone correction
The time zone correction is needed for countries where the DCF signal can be received but the
time zone is different from the DCF time (e.g. +1=one hour plus).
11
Day-of-the week language
In the setting mode you can set the day-of-the week language: GERMAN, FRENCH, ITALIAN,
SPANISH, DANISH, DUTCH, CZECH, POLISH, SWEDISH and ENGLISH
Alarm time setting
Press the MODE/SET button (Fig.2-A) in normal mode to enter the alarm mode. ALARMTIME and
7:00 (default) or the last adjusted alarm time appear on the display.
Press and hold the MODE/SET button for three seconds to enter the setting mode.
The hour digits flash.
Press the  or / button to set the hours.
Confirm the setting with the MODE/SET button and set minutes in the same way.
Press the MODE/SET button again to return to the current time.
To activate/turn off the alarm function, press ALARM ON/OFF button (Fig.2-D).
The alarm symbol (Fig.1-D) appears/disappears on the display.
The switch at the back (Fig.2-I) allows you to choose between two different alarm functions
(Monday to Friday or Monday to Sunday).
When the alarm is activated, the alarm starts to ring when the set alarm time is reached.
The alarm symbol flashes.
Press any button (except SNOOZE (Fig.2-F)) and the alarm will stop.
Press the SNOOZE button (Fig.2-F) to activate the snooze function.
The alarm will be interrupted for about 5 minutes.
Outdoor temperature alarm
Press and hold the ALERT button (Fig.2-G) for 3 seconds.
and 50 °C (default) or the last adjusted upper temperature limit appear on the display.
Press the  or / button to adjust the desired upper temperature limit.
Confirm with the ALERT button.
and -20°C (default) or the last adjusted lower temperature limit appear on the display.
Press the  or / button to adjust the desired lower temperature limit.
Confirm with the ALERT button.
To activate/turn off the alarm function, press ALERT button.
The respective symbol will appear or disappear on the display (Fig.1-I).
In the event of an alarm, the corresponding symbol will be flashing and an alarm tone will sound.
Stop the alarm sound with any button.
12